Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operation
!
Serious danger!
Vehicle tyres and tyre valves can be damaged by the
high-pressure jet and become perforated. The first
sign of this is a discoloration of the tyre. When cle-
aning them maintain a distance of at least 30 cm.
Never grasp the power plug with wet hands.
Before each use check the power cord and power
plug for damage. Have a damaged power cord repla-
ced immediately by an authorized service point or an
electrical specialist.
Before each use check the high-pressure hose for
damage. Replace a damaged high-pressure hose
immediately.
!
Danger of injury!
Owing to the water jet emerging from the high-pres-
sure nozzle a recoil force operates on the handgun.
Ensure you have a secure footing and hold the hand-
gun and spray lance firmly.
If necessary wear protective clothing for protection
against return spray.
Water supply
Caution! Impurities in the intake water damage the
pump. To prevent this we expressly urge you to use
a water filter.
The operation of the high-pressure cleaner with a clo-
sed water supply line causes damage to the cylinder
head unit. Please never operate the high-pressure
cleaner with a closed water supply tap.
The unit can either be supplied from the water main
or from water in an open container.
Water supply from the water main
• Connect a supply hose (not included) to the water
inlet of the unit and to the water supply (e.g. water
tap).
• Open the water supply.
Water supply from an open container
• Unscrew the coupling part for the water inlet.
• Screw the suction hose with filter onto the water con-
nection of the unit.
• Hang the filter in the container.
• Vent the unit before operation.
– Unscrew the high-pressure line at the high-pres-
sure outlet of the unit.
– Switch on the unit and let it run until water free
of bubbles emerges at the high-pressure outlet.
– Switch off the unit and screw on the high-pres-
sure hose again.
Preparation
• Insert power plug.
• Turn master switch to "I".
Switching on
• Press safety button on the handgun and pull the
lever.
Switching off
• Release the lever.
During breaks in work and when leaving the unit se-
cure it against inadvertent switching on by pressing
the safety button.
Regulate operating pressure
Raise operating pressure:
• twist spray lance in direction
Reduce operating pressure:
• twist spray lance in direction
Adding the cleaning agent
• Draw the cleaning agent metering valve out of its
holding bracket.
• Draw the cleaning agent suction hose out of the
housing to the required length.
• Hang the cleaning agent metering valve in the cle-
aning agent container.
• Twist the spray lance in the "
the stop.
If cleaning agent has been added:
• Hang the cleaning agent metering valve in a container
of clear water, switch on the unit for about one mi-
nute and flush through.
Recommended cleaning method
1. Spray the cleaning agent on the dry surface spa-
ringly and let it react (but not dry out).
2. Wash off the loosened dirt with the high-pressure
jet.
Connect accessories
• Exchange the accessory with the spray lance.
Rotary nozzle
for stubborn accumulations of grime – e.g. moss-
covered promenade tiles or facades.
Work without cleaning agent and with the highest
operating pressure.
Finishing operations
• Master switch to "0".
• Draw out power plug.
Water supplied from the water main
• Close the water supply tap.
• Separate the unit from the water connection.
Water supplied from an open container
• Unscrew the suction hose with filter at the water inlet
of the unit.
• Pull the lever on the handgun until the unit is without
pressure.
• Press in the safety button to protect the unit against
inadvertent switching on.
Safekeeping
Caution! Frost can destroy an incompletely emptied
unit. In the winter keep the unit in a frost-free room.
• Separate the spray lance from the handgun.
• Wind up the power cord and, for example, hang it
around the handgun.
" direction until
English - 13
Werbung
