Protecting The Environment; Technical Data - Black & Decker REVOS12C Bersetzt Von Den Originalanweisungen

ENGLISH
Note: The spacer and fixing bolt are not used to attach
BLACK+DECKER accessories. BLACK+DECKER
accessories are attached using the Super-lok
accessory clamping lever.
Switching on and off (fig. G)
To switch the tool on, press the on/off switch (1)
u
(position I).
To switch the tool off, press the on/off switch (1)
u
(position O).
Hints for optimum use
Always hold the tool securely. For precision work, hold the
u
tool near the front.
Clamp the workpiece whenever possible, especially when
u
using cutting blades.
Do not exert too much pressure on the tool.
u
Always use the appropriate type of attachment for the
u
workpiece material and type of cut.
Regularly check the condition of accessories. Replace
u
when necessary.
Mark the desired starting point.
u
Switch the tool on and slowly feed attachments into the
u
workpiece at the desired starting point.
Clamp a piece of plywood or soft wood to the back of the
u
workpiece and saw through the combination in order to
obtain a clear cut.
Do not force the cutting blade into the workpiece. Note
u
that cutting sheet metal will normally take more time than
sawing thicker wooden workpieces.
When cutting metal spread a thin film of oil along the cut-
u
ting line before cutting.
When sanding new layers of paint before applying another
u
layer, use extra fine grit.
On very uneven surfaces, or when removing layers of
u
paint, start with a coarse grit. On other surfaces, start with
a medium grit. In both cases, gradually change to a fine
grit for a smooth finish.
Consult your retailer for more information on available
u
accessories.
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
u
tool if the appliance/tool has a separate battery pack.
10
(Original instructions)
Tool free
TM
Or run the battery down completely if it is integral and then
u
switch off.
Regularly clean the ventilation slots in your appliance/tool/
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new
u
plug.
Connect the blue lead to the neutral terminal.
u
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.

Protecting the environment

Z
Separate collection. Products and batteries marked
with this symbol must not be disposed of with
normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com.

Technical data

Voltage V
DC
No-load speed
min
-1
Oscillating angle Degrees
Weight kg
Battery type
Charger
Input Voltage V
AC
Output Voltage V
DC
Current A
Level of sound pressure according to EN62841:
Sound pressure (L ) 72 dB(A), uncertainty (K) 3 dB(A)
pA
Sound power (L ) 83 dB(A), uncertainty (K) 3 dB(A)
WA
Vibration total values (triax vector sum) according to EN62841:
(a ) - 4.1 m/s uncertainty K - 1.5 m/s
2 2
h
REVOS12C
12
11000
2.8
0.906
Li-Ion
S010**1400040
100 - 240
14
0.4