Safety Of Others - Black & Decker REVOS12C Bersetzt Von Den Originalanweisungen

ENGLISH
e. Do not use a battery pack or tool that is damaged or
modified. Damaged or modified batteries may exhibit
unpredictable behaviour resulting in fire, explosion or risk
of injury.
f. Do not expose a battery pack or tool to fire or
excessive temperature. Exposure to fire or temperature
above 130 °C may cause explosion.
g. Follow all charging instructions and do not charge the
battery pack or tool outside the temperature range
specified in the instructions. Charging improperly or at
temperatures outside the specified range may damage the
battery and increase the risk of fire.
6. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
b. Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
Additional power tool safety warnings
@
Warning! Warning! Additional safety warnings
for Oscillating tools
Hold power tool by insulated gripping surfaces, when
u
performing an operation where the cutting accessory
may contact hidden wiring. Cutting accessory contact-
ing a "live" wire may make exposed metal parts of the
power tool "live" and could give the operator an electric
shock.
Use clamps or another practical way to secure and
u
support the workpiece to a stable platform.
Holding the work by hand or against your body leaves it
@ unstable and may lead to loss of control.
Warning! Contact with or inhalation of dusts
arising from sanding applications may endanger
the health of the operator and possible bystand-
ers. Wear a dust mask specifically designed for
protection against dust and fumes and ensure
that persons within or enteringthe work area are
also protected.
Thoroughly remove all dust after sanding.
u
Take special care when sanding paint which is pos-
u
sibly lead based or when sanding some woods and
metal which may produce toxic dust:
Do not let children or pregnant women enter
u
the work area.
Do not eat, drink or smoke in the work area.
u
6
(Original instructions)
Dispose of dust particles and any other
u
debris safely.
The intended use is described in this instruction manual.
u
The use of any accessory or attachment or performance
of any operation with this tool other than those
recommended in this instruction manual may present a
risk of personal injury and/or damage to property.
The accessory will continue to move after releasing
u
the switch. Always switch the tool off and wait for the
accessory to come to a complete standstill before putting
the tool down.
Keep hands away from cutting area. Never reach
u
underneath the work piece any reason.
Do not insert fingers or thumb into the vicinity of the
reciprocating blade and blade clamp. Do not stabilize the
saw by gripping the shoe.
Keep blades sharp. Dull or damaged blades may cause
u
the saw to swerve or stall under pressure. Always use the
appropriate type of saw blade for the workpiece material
and type of cut.
When cutting pipe or conduit, make sure that they are
u
free from water, electrical wiring, etc.
Do not touch the workpiece or the blade immediately
u
after operating the tool. They can become very hot.
Be aware of hidden hazards, before cutting into walls,
u
floors or ceilings, check for the location of wiring and
pipes.
Always wear hearing protection.
u

Safety of others

This appliance is not intended for use by persons (includ-
u
ing children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concern-
ing use of the appliance by a person responsible for their
safety.
Children should be supervised to ensure that they do not
u
play with the appliance.
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured in
accordance with a standard test method provided by EN62841
and may be used for comparing one tool with another. The
declared vibration emission value may also be used in a
preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.