Endress+Hauser Nivector FTI26 Betriebsanleitung Seite 20

Systemintegration
Bezeichnung ISDU
(dez)
Switching delay 81
time Output 1 (dS1)
Switchback delay 82
time Output 1 (dR1)
Output mode Out- 85
put 1
Full adjustment, 88
Output 2
Covered value Out- 273
put 2
Switch point value 75
Output 2 (SP2/FH2)
Switchback point 76
value Output 2
(rP2/FL2)
Switching delay 83
time Output 2 (dS2)
Switchback delay 84
time Output 2 (dR2)
Output mode Out- 86
put 2
Parameter - System
Operating hours 96
uC-Temperature 91
Unit changeover 80
(UNI) – uC-Tempe-
rature
Minimum uC-Tem- 92
perature
Maximum uC-Tem- 93
perature
Reset uC-Tempera- 94
ture
Diagnosis
Simulation switch 89
Output 1 (OU1)
Simulation switch 68
Output 2 (OU2)
Device search 69
Sensor check 70
1) Auslieferzustand hängt von den bestellten Optionen ab.
2) Erklärung der Abkürzungen siehe Parameterbeschreibung.
20
ISDU (hex) Grösse Datentyp Zugriff Default
(byte)
0x0051 2 Uint16
0x0052 2 Uint16
0x0055 1 Uint8
0x0058 1 Uint8
0x0111 2 Int16
0x004B 2 Uint16
0x004C 2 Int16
0x0053 2 Int16
0x0054 2 Uint16
0x0056 1 Uint8
0x0060 4 Uint32
0x005B 1 Int8
0x0050 1 Uint8
0x005C 2 Int16
0x005D 2 Int16
0x005E 1 Uint8
0x0059 1 Uint8
0x0044 1 Uint8
0x0045 1 Uint8
0x0046 1 Uint8
Wertebereich
value
r/w 0,5s
r/w 1,0s
r/w HNO 0 ~ HNO
2)
1 ~ HNC
2 ~ WNO
3 ~ WNC
w 1
1)
r/w
1)
r/w
1)
r/w
r/w 0,5s
r/w 1,0s
r/w HNC 0 ~ HNO
1 ~ HNC
2 ~ WNO
3 ~ WNC
r
r
r/w °C 0 ~ °C
1 ~ °F
2 ~ K
r 127
r -128
w 1
r/w Off 0 ~ Off
1 ~ high
2 ~ low
r/w Off 0 ~ Off
1 ~ high
2 ~ low
r/w Off 0 ~ Off
1 ~ On
w 1
Nivector FTI26
Offset/Gain Data
Sto-
rage
0/0,1 ja
0/0,1 ja
2)
0... ja
2)
2)
0/0 ja
0/0 ja
0/0 ja
0/0,1 ja
0/0,1 ja
2)
ja
2)
2)
2)
0 / 0.016667 nein
°C: 0 / 1 nein
°F: 32 / 1.8
K: 273.15 / 1
0/0 ja
°C: 0 / 1 nein
°F: 32 / 1.8
K: 273.15 / 1
°C: 0 / 1 nein
°F: 32 / 1.8
K: 273.15 / 1
0/0 nein
0/0 nein
0/0 nein
0/0 nein
Endress+Hauser
Bererichs-
grenzen
0,3 ... 60
0,3 ... 60
0...3
0...400
0...400
0...400
0,3 ... 60
0,3 ... 60
0...3
0...2^32
-128...127
0...2
-128...127
-128...127
0...2
0...2
0...1