Optional Accessory - Makita VC009G Betriebsanleitung

3. Follow the procedures below, depending on the
type of the extension wand :
NOTE: The slide-type extension wand and the ring-
type extension wand are not compatible with each
other. If you want to change the slide-type extension
wand to the ring-type extension wand or vice versa,
change the bent pipe assembly also.
For the slide-type extension wand
Shoulder the vacuum cleaner body then insert the extension
wand into the bent pipe assembly until it clicks. To discon-
nect, extract the extension wand with pressing the button.
► Fig.18: 1. Bent pipe assembly 2. Button 3. Slide-
type extension wand
The length of the wand can be adjusted.
With pressing the slide button, adjust the wand length.
The length is locked when releasing the slide button.
► Fig.19: 1. Slide button
For the ring-type extension wand
Shoulder the vacuum cleaner body then twist and insert
the extension wand into the bent pipe assembly. To
disconnect, twist and extract it.
► Fig.20: 1. Bent pipe assembly 2. Ring-type exten-
sion wand 3. Free nozzle
NOTE: The free nozzle can be attached to the bent
pipe assembly without pipe lock directly.
The length of the wand can be adjusted.
Loosen the ring on the wand and adjust the wand
length. Tighten the ring at your desired length.
► Fig.21: 1. Ring
Hose hook
When you suspend the operation, the hook on the bent pipe
assembly can be used for hanging the wand on the lower belt.
► Fig.22: 1. Hook 2. Lower belt
Installing filter bag / dust bag

Optional accessory

CAUTION:
Do not use a damaged filter bag.
Always use the vacuum cleaner with the filter bag
properly installed. Otherwise the vacuumed dust or
particles may be exhausted from the cleaner and they
may cause respiratory disease to the operator.
NOTICE:
When the filter bag is already full,
replace with new one. When the dust bag is
already full, empty it. Continuous use with the filter
bag/dust bag full results in reduced suction power.
NOTICE:
To prevent dust from getting into the motor:
— Make sure that the filter bag/dust bag is
installed before use.
Do not use a broken or ripped bag.
—
Otherwise the motor may be broken.
NOTICE:
Do not fold the cardboard at its open-
ing when installing the filter bag/dust bag.
NOTICE:
The filter bag/dust bag for the cleaner
is an important component for maintaining the
appliance performance. Using non-genuine filter
bag/dust bag may cause smoke or ignition.
NOTE: When the filter bag/dust bag is not installed in
the cleaner, the front cover does not close completely.
► Fig.23
1.
Unlock the lever and open the dust box cover.
► Fig.24: 1. Lever 2. Dust box cover
2. Insert the filter bag into the slit on the upper side of
the room as illustrated.
► Fig.25: 1. Slit 2. Filter bag
When using the dust bag, insert the brim of the dust bag
into the slit.
► Fig.26: 1. Slit 2. Brim 3. Dust bag
3.
Align the hole of the filter bag with the hose cuff
and push the cardboard portion to the end. Make sure
that the rubber ring on the filter bag goes over the rim
on the hose cuff.
► Fig.27: 1. Rubber ring on the filter bag 2. Rim on
the hose cuff 3. Cardboard portion of the
filter bag 4. Hose cuff
4.
Lock the dust box cover certainly.
CAUTION:
Be careful not to pinch your fin-
gers when hooking the latch, and when closing
the dust box cover.
OPERATION
WARNING:
instructed on the use of the vacuum cleaner.
WARNING:
able for picking up hazardous dust.
CAUTION:
This cleaner is for dry use only.
CAUTION:
Always insert the battery cartridge
all the way until it locks in place. If you can see the
red indicator on the upper side of the button, it is not
locked completely. Insert it fully until the red indicator
cannot be seen. If not, it may accidentally fall out of the
tool, causing injury to you or someone around you.
CAUTION:
During operation, be conscious
of the vacuum cleaner on your back. You may
lose your balance if the vacuum cleaner body bumps
against a wall or the hose is hooked by an obstacle.
1. Shoulder the vacuum cleaner body and fas-
ten lower and upper belts. Adjust the tightness as
necessary.
► Fig.28
2.
Press button to start vacuuming. If you want
to change the suction power, press
desired suction power is selected. Press
stop.
► Fig.29
During the operation, hook the switch box on the lower
belt or the D-ring.
► Fig.30
17 ENGLISH
Operators shall be adequately
This vacuum cleaner is not suit-
button until the
button to