Instructions For Use; Sauna Climate Control; Using The Device; Instructions For Using Himalayan Salt Balls - Saunum BASE Bedienungs- Und Installationsanleitung

INSTRUCTIONS FOR USE

The Device is designed for harmonising the
climate of the steam room during a steam
session.
Before using the Device for the first
time, check:
• compliance of the wiring with the
requirements;
• compliance of the supply voltage
with the rated voltage of the Device;
• the condition of the protective
earthing (PE);
• the mountings on the Device hous-
ing;
• the wall mountings of the Device;
• the condition / presence of overcur-
rent and residual-current protection
devices;
• if the fan rotor can rotate freely;
• if all tools and residues of the
materials used during installation
are removed from the housing of
the Device.
When starting the Device, check:
• the direction of air flow – air must
be drawn from the upper and
blown out from the lower opening;
• for abnormal vibration or noise
when the fan is running;
• the lighting stability for LED
equipped devices.
30
SAUNA CLIMATE
CONTROL
The volume of air circulated by the Device
can regulated by a rotary switch located on
the lower right side of the Device.
The switch has four positions and can be
turned both clockwise and counter-clock-
wise. When the bar on the switch button
points to the left, the Device's fan is turned
off. Airflow speed increases by turning the
switch clockwise, you can choose between
three different speeds. (Exept Base S with
external switch.)
To control the air temperature in the steam
room, an air-cooling damper for steam is
located on the bottom front panel of the
Device (see Figures 1C and 2B). The recom-
mended setting is to keep the cooling
damper 1/3 open. To cool the steam, try
opening the damper incrementally. Try us-
ing different fan speeds to find the perfect
indoor climate for your sauna.

USING THE DEVICE

The Device is to be switched on immedi-
ately before entering the steam room and
switched off immediately after leaving
the steam room. The Device may not be
switched on when heating the steam room
or when there is no one in the steam room,
as the operation of the Device will increase
the temperature in the lower part of the
steam room and the bench and floor may
become too hot.
To ensure long service life of the Device,
make sure that the temperature in the
steam room at the lower part of the
Device does not exceed 80 °C. If this
temperature is exceeded, the thermal pro-
tection will activate and the fan will stop;
once the temperature falls below the acti-
vation level of the protection, the fan will
be switched on again.
The manufacturer will not be held liable for
equipment failures resulting from exceed-
ing the permitted operating temperature.
If your Device is equipped with internal
lights, the lights will activate at the same
time as the fan (see the marking on the
packaging of the Device) when the Device
is switched on.
If your Device is wall-integrated and
equipped with an external touch-
sensitive switch for speed control,
please keep in mind the following
requirements:
• The external speed switch may
only be installed outside the steam
and washing room, e.g., the chang-
ing room, preferably next to the
door, so that the Device can be
conveniently switch on and off.
• The switch has three positions for
selecting the desired airflow inten-
sity. The Device can be switched on
and off by pressing and holding
the touch-sensitive button of the
desired speed.
• Touch the appropriate area to
select speeds.
• If the Device is equipped with
internal lighting, a separate switch
(optional) must be used to switch
it on.
INSTRUCTIONS FOR USING
HIMALAYAN SALT BALLS
The sauna climate unit comes with Hima-
layan salt balls. The use of salt balls in the
Device is optional and does not affect the
basic function of the Device.
To use the salt balls, they must be placed in
the base tray located between the air dis-
charge grille and the fan. Make sure that
the salt balls are placed correctly and do
not impede the rotation of the fan.
To place or remove the salt balls (see
Figures 1D and 2C), loosen the two fasten-
ing bolts on the discharge grille and lower
the grille on its hinges. Do not use excessive
force! After placing or removing the salt
balls, shut the discharge grille and fasten it
with two bolts.
The sauna climate unit may only be used
if the grille is installed!
31