Before Starting The Equipment; Fitting The Battery - EINHELL CE-CP 18/180 Li E Originalbetriebsanleitung

Operating mode: Sanding with sanding paper
Vibration emission value a
K uncertainty = 1.5 m/s
Operating mode: Polishing
Vibration emission value a
K uncertainty = 1.5 m/s
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
•
Fit the handles and, if applicable, the optional
anti-vibration handles securely to the machi-
ne body.
If you experience an unpleasant feeling or skin
discoloration on your hands while using the ma-
chine, stop your work immediately. Take adequate
breaks from your work. If you do not take ade-
quate breaks from your work, you could develop
hand-arm vibration syndrome.
You should evaluate the level of strain in relation
to the work involved and the use of the machine
and take adequate work breaks accordingly. This
will enable you to signifi cantly reduce the level
of strain over the whole period of work. Minimize
the risk to which you are exposed from vibrations.
Look after this machine with care in accordance
with the operating instructions.
If the machine is deployed or used often, you
should consult your dealer and possibly consider
obtaining anti-vibration accessories (handles).
Anl_CE_CP_18_180_Li_E_Solo_SPK13.indb 19 Anl_CE_CP_18_180_Li_E_Solo_SPK13.indb 19
= 5,194 m/s
2
h,DS
2
= 4.275 m/s
2
h,P
2
- 19 -
GB
Do not use the machine at temperatures of
t=10°C or lower. Think out a work plan which ena-
bles you to limit your exposure to vibrations.
A certain level of noise nuisance is inevitable with
this equipment. Carry out noise-intensive jobs
at times that are acceptable and allowed. Where
applicable, observe rest periods and restrict your
working time to a minimum. Suitable ear protec-
tion must be worn for your own safety and for the
safety of others nearby.

5. Before starting the equipment

Only press the spindle lock when the equipment
is at a standstill.
5.1 Assembling the equipment (Fig. 4-6)
Important! Remove the rechargeable battery be-
fore starting the assembly work.
The equipment is supplied without batteries
and without a charger.

5.2. Fitting the battery

Press the side pushlock button (c) of the battery
pack as shown in Fig. 9 and push the battery
pack into the mount provided. When the battery
is positioned as in Fig. 9, make sure that the
pushlock button latches in place! To remove the
battery pack, proceed in reverse order.
5.3 Charging the battery (Fig. 7)
1. Take the battery pack out of the equipment.
Do this by pressing the pushlock button.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
into the socket outlet. The green LED will then
begin to fl ash.
3. Insert the battery pack (11) into the battery
charger (10).
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
11.04.2022 13:14:24 11.04.2022 13:14:24