Bosch GOF 2000 CE Professional Originalbetriebsanleitung Seite 26

26 | English
When routing with the parallel guide 26, the
dust/chip extraction should take place via the
special extraction adapter for the parallel guide
32. The extraction adapter 24 can remain
mounted.
Routing with the Router Compass
(see figure F)
The router compass/guide-rail adapter 33 can
be used for circular routing jobs. Mount the
router compass as shown in the figure.
Screw the centring screw 38 into the thread on
the router compass. Insert the point of the cen-
tring screw into the centre of the circular arc to
be routed, paying attention that point of the
screw engages into the workpiece surface.
Coarsely adjust the required radius by moving
the router compass and tighten the wing bolts
35 and 36.
The length can be fine adjusted with the fine-ad-
justment knob 37 after loosening the wing bolt
36. One revolution corresponds with a setting
range of 2.0 mm. One graduation mark on the
fine-adjustment knob 37 changes the setting
range by 0.1 mm.
Guide the switched on power tool over the
workpiece with the right handle 1 and the router
compass handle 34.
Routing with Guide Rail (see figure G)
Straight routing cuts can be carried out with
help of the guide rail 40.
The base spacer 39 must be mounted in order to
compensate the height difference.
Mount the router compass/guide-rail adapter 33
as shown in the figure.
Fasten the guide rail 40 to the workpiece with
suitable clamping devices, e. g. screw clamps.
Place the machine with the guide-rail adapter 33
mounted onto the guide rail.
Routing with Guide Bushing (see figures H–L)
The guide bushing 44 enables template and pat-
tern routing on workpieces.
In order to use the guide bushing 44, the guide
bushing adapter 41 must be inserted into the
guide plate 12 first.
1 609 929 N94 | (3.9.08)
Place the guide bushing adapter 41 from above
onto the guide plate 12 and tighten it firmly with
the 2 fastening screws 42. Pay attention that
the release lever for the guide bushing adapter
43 is freely movable.
Choose a suitable guide bushing, depending on
the thickness of the template or the pattern. Be-
cause of the projecting height of the guide bush-
ing, the template must have a minimum thick-
ness of 8 mm.
Actuate the release lever 43 and insert the guide
bushing 44 from below into the guide bushing
adapter 41. Ensure that the encoding keys clear-
ly engage in the grooves of the guide bushing.
Select a router bit with a diameter smaller
than the interior diameter of the guide
bushing.
To ensure that the distance from router bit cen-
tre and guide bushing edge is uniform, the guide
bushing and the guide plate can be adjusted to
each other, if required.
– Push the release lever 16 down and guide the
router to the stop in the direction of the base
plate 14. Let go of the release lever 16 again,
in order to lock this plunging depth.
– Loosen the fastening screws 45 by approx.
2 – 3 turns so that the guide plate 12 can be
moved freely.
– Insert the centring pin 46 into the tool holder
as shown in the figure. Hand-tighten the
tightening nut so that the centring pin can
still be moved freely.
– Align the centring pin 46 and the guide bush-
ing 44 to each other by slightly moving the
guide plate 12.
– Tighten the fastening screws 45.
– Remove the centring pin 46 from the tool
holder.
– Push the release lever 16 and guide the
plunge router to the uppermost position.
For routing with the guide bushing 44 proceed
as follows:
– Guide the switched on power tool with the
guide bushing toward the template.
Bosch Power Tools