Maintenance - Ferm 326110 Gebrauchsanweisung

VEDLIGEHOLDELSE
Sørg for at maskinen ikke står under strøm, når
der udføres vedligeholdelsesarbejder på meka-
nikken.
Maskinerne fra Ferm er udviklet til at fungere lœnge
uden problemer med et minimum af vedligehol-
delse. Ved at rengøre maskinen regelmœssigt og
behandle den korrekt, bidrager De til en lœngere
levetid for maskinen.
Rengøring
Rengør regelmœssigt maskinkappen med en blød klud,
helst efter hvert brug. Sørg for at ventilationshullerne er fri
for støv og snavs.
Brug en blød klud, der er vœdet i sœbevand til at fjerne
hårdnakket snavs. Brug ingen opløsningsmidler, så som
benzin, alkohol, ammoniak, osv. Den slags stoffer beska-
diger kunststofdelene.
Smøring
Maskinen behøver ingen ekstra smøring.
Fejl
Kontakt Deres Ferm-forhandler, hvis der opstår fejl som
følge af slitage af en del.
Bagerst i denne brugsanvisning finder De en reservedel-
stegning med de reservedele, der kan bestilles.
MILJØ
For at undgå transportbeskadigelse leveres maskinen i
en solid emballage. Emballagen er så vidt muligt lavet af
genbrugsmateriale. Genbrug derfor emballagen.
Når de udskifter Deres maskinen bør De tage den gamle
maskine med til Deres lokale Ferm-forhandler. Der vil
maskinen blive bearbejdet på miljøvenlig vis.
GARANTI
Lœs det separat vedlagte garantikort for garantibetingel-
serne.
36
■
ClEl
( DK )
KONFORMITETSERKLÆRING
Vi erklærer at under almindeligt ansvar, at dette
produkt er i overenstemmelse med følgende
normer eller normative dokumenter
EN50144-1, EN50144-2-17,
EN55014-1, EN55014-2,
EN61000-3-2, EN61000-3-3
i henhold til bestemmelserne i direktiverne:
98/37EEC
73/23EEC
89/336EEC
01-11-1999
GENEMUIDEN NL
G.M. Ensing
Quality department
Adjusting the cutting depth
11
12
10
Fig. E
The cutting depth can be adjusted in two ways.
Adjustment using the scale
• Loosen the locking bolt of the depth stop (12).
• Release clamping lever (3) and press the machine so
far down until the cutter touches the workpiece.
• Tighten the clamping lever again.
• Set the desired cutting depth using the graduated sca-
les (11) and then tighten the clamp screw.
Adjustment using the revolver- depth stop
The revolver-depth stop enables you to quickly choose
between three different cutting depths. These are also
determined by the adjustment of the depth scale (11).
• Adjust the required cutting depth by the three screws
on the revolver-depth stop (10).
Switching on and off (Fig. A).
• Depress the on/off switch (1) to switch the machine on.
Then push the switch through its resistance to lock the
switch in the on position. The cutter speed can be
adjusted by means of the adjusting wheel (13).
• Release the on/off switch to switch the machine off or
push the switch again when it is in locked position.
Always select a low speed for cutting plastic
workpieces.
Do not put the machine down when the motor is still run-
ning. Do not place the machine on a dusty surface. Dust
particles may enter the mechanism.
Ferm Ferm

MAINTENANCE

Make sure that the machine is not live when car-
rying out maintenance work on the motor.
3
The Ferm machines have been designed to operate over
a long period of time with a minimum of maintenance. Con-
tinuous satisfactory operation depends upon proper
machine care and regular cleaning.
Cleaning
Regularly clean the machine housing with a soft cloth, pre-
ferably after each use. Keep the ventilation slots free from
dust and dirt.
If the dirt does not come off use a soft cloth moistened with
soapy water. Never use solvents such as petrol, alcohol,
ammonia water, etc. These solvents may damage the
plastic parts.
Lubrication
The machine requires no additional lubrication.
Faults
Should a fault occur, e.g. after wear of a part, please con-
tact your local Ferm dealer.
In the back of this manual you find an exploded view
showing the parts that can be ordered.
ENVIRONMENT
In order to prevent the machine from damage during trans-
port, it is delivered in a sturdy packaging. Most of the pack-
aging materials can be recycled. Take these materials to
the appropriate recycling locations.
Take your unwanted machines to your local Ferm-dealer.
Here they will be disposed of in an environmentally safe
way.
GUARANTEE
The guarantee conditions can be found on the separately
enclosed guarantee card.
■
ClEl
DECLARATION OF CONFORMITY
We declare under our sole responsability that this
product is in conformity with the following
standards or standardized documents
EN55014-1, EN55014-2
EN50144-1, EN50144-2-17,
EN61000-3-2, EN61000-3-3,
in accordance with the regulations.
98/37EEC, 73/23EEC, 89/336EEC
from 01-11-1999
GENEMUIDEN NL
G.M. Ensing
Quality department
( GB )
5