VONROC MS507AC Originalbetriebsanleitung Seite 18

EN
Subsequently check the position of the angle indica-
tor (19). If necessary loosen the pointer using a Phi-
lips screwdriver, set to position 0° on the scale for
bevel angle (20) and re-tighten the retaining screw.
Fine-tuning the 45° bevel angle (Fig. R, T)
1. Adjust the mitre and bevel angle to 45°;
2. Lower the handle (2) and secure it using the
position lock knob (38);
3. Lock the slide movement using the locking bolt
for slide rails (29);
4. Set an angle gauge to 90° and place it on the
table (11), as shown on figure T. The leg of the
angle gauge must be flush with the saw blade
(6) along its entire length;
5. Loosen the lock nut for 45° bevel angle (49);
6. Adjust the stop bolt for 45° bevel angle (31)
until the leg of the angle gauge is flush with the
saw blade along its entire length;
7. Re-tighten the lock nut for 45° bevel angle (49).
Subsequently check the position of the angle indi-
cator (19). If necessary loosen the pointer using a
Philips screwdriver, set to position 45° on the scale
for bevel angle (20) and re-tighten the retaining
screw.
Fine-tuning the 0° mitre angle (Fig. U, V)
1. Set an angle gauge to 0° on the table (11) and
position it between the fence (9) and the saw
blade (6);
2. The leg of the angle gauge must be flush with
the saw blade (6) along its entire length;
3. Loosen all four fence bolts (51) and adjust the
fence (9) until the leg of the angle gauge is
flush with the saw blade along its entire length;
4. Retighten all four fence bolts (51) again. Subse-
quently check the position of the angle indicator
(17). If necessary loosen the pointer using a
Philips screwdriver, set to position 0° on the scale
for mitre angle (16) and re-tighten the retaining
screw.
5. MAINTENANCE
Always make sure that the machine is not
connected to the mains electricity when you
carry out any maintenance of the mechanism.
Clean the machine casings regularly with a soft
cloth, preferably after each use. Make sure that the
18
ventilation openings are free of dust and dirt. Re-
move very persistent dirt using a soft cloth moiste-
ned with soapsuds. Do not use any solvents such
as gasoline, alcohol, ammonia, etc. Chemicals such
as these will damage the synthetic components.
Cleaning the protective guards
Always check the protective guard (4) and retracta-
ble protective guard (5) for debris before using the
machine. Remove old sawdust and splinters using
a brush or similar tool.
Replacing the table insert
Immediately replace damaged table inserts.
With a damaged table insert (13) there is a risk of
small parts getting stuck between table insert and
saw blade, blocking the saw blade. To replace the
table insert:
1. Remove screws of table insert using a Philips
screw driver. If required, adjust mitre and bevel
angle to obtain access these screws;
2. Remove table insert;
3. Install new table insert;
4. Tighten the screws using a Philips screw driver.
Slide rails
Dirt can damage the slide rails (25) and thereupon
the operating of the machine.
• Clean the slide rails regularly with a soft cloth;
• Drip some lubricating oil on the slide rails;
• Move the mitre saw forwards and backwards so
the oil spreads over the complete rails.
ENVIRONMENT
Faulty and/or discarded electrical or
electronic apparatus have to be collected at
the appropriate recycling locations.
Only for EC countries
Do not dispose of power tools into domestic waste.
According to the European Guideline 2012/19/
EU for Waste Electrical and Electronic Equipment
and its implementation into national right, power
tools that are no longer usable must be collected
separately and disposed of in an environmentally
friendly way.
WWW.VONROC.COM