Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Maintain your radial tile cutter with care:
− Keep the tools sharp and clean to be able to work better
and more safely.
− Follow the servicing instructions and the information
about changing tools.
− Keep handles dry and free of oils and grease.
Check the machine for possible damage:
− Before continuing to use the machine, the protective
devices must be inspected to ensure that they work
perfectly and with their intended function
− Check whether the movable parts function perfectly
and do not stick or whether the parts are damaged, All
parts must be correctly installed and fulfil all conditions
to ensure perfect operation of the radial tile cutter
− Damaged guards and parts must be properly repaired
or exchanged by a recognized, specialist workshop;
insofar as nothing else is stated in the instructions for
use.
− Damaged or illegible safety warning labels should be
replaced immediately.
Do not allow any tool key to be plugged in!
Store the unused machine in a dry locked place away from
the reach of children.
Do not carry power tools with the finger placed on the
switch. Make sure that the switch is off before connecting
the mains plug with the outlet socket.
Electrical safety
Design of the connection cable according to IEC 60 245
(H 07 RN-F) with a core cross-profile section of at least
1.5 mm
for cable lengths up to 25 m
2
2.5 mm
for cable lengths over 25 m
2
Long and thin connection lines result in a potential drop.
The motor does not reach any longer its maximal power; the
function of the device is reduced.
Plugs and coupler outlets on connection cables must be
made of rubber, non-rigid PVC or other thermoplastic
material of same mechanical stability or be covered with this
material.
The connector of the connection cable must be splash-
proof.
When running the connection line observe that it does not
interfere, is not squeezed, bended and the plug connection
does not get wet.
Do not use the cable for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges. Do
not use the cable to pull the plug from the socket.
Wind off completely the cable when using a cable drum.
Regularly check the extension cables and replace them if
they are damaged.
Do not use any defective connection cables.
When working outdoors, only use extension cables
especially approved and appropriately labelled for outdoor
use.
Do not set up any provisional electrical connections.
Never bypass protective devices or deactivate them.
The device must be connected via the fitted PRCD
(residual-current-operated circuit breaker).
The electrical connection or repairs to electrical parts of
the machine must be carried out by a certified electrician
or one of our customer service points. Local regulations –
especially regarding protective measures – must be
observed.
Repairs to other parts of the machine must be carried out
by the manufacturer or one of his customer service
points.
Use only original spare. Accidents can arise for the user
through the use of other spare parts. The manufacturer
is not liable for any damage or injury resulting from such
action.
D
e
s
c
r
i
p
t
i
o
n
o
D
e
s
c
r
i
p
t
i
o
n
o
Pos. Bezeichnung
1.
Supporting leg
Indicator for longitudinal cutting
2.
3.
Closing plug
4.
Star handled screw M8 x 12
5.
Trough
6.
Table plate
7.
Stopper bar (2 pieces) with scale
8.
Angle fence
9.
Star handled nut M6 for angle adjustment
10.
Guide bar
11.
Scale for mitre cut
12.
Stopper for longitudinal section/transport
13.
Cutting unit
14.
On-off switch
15.
Fan (not illustrated)
16.
Fan cooling
17.
Capacitor (not illustrated)
18.
Handhold
Locking screw for mitre cut
19.
Splash guard
20.
Hose
21.
Covering cap
22.
23.
Cooling water pump
24.
Screw M5 x 12
25.
Disc A 5.3 mm
26.
Spring washer A Ø 5mm
27.
Front flange
28.
Cutting-off wheel Ø 200 x Ø 25.4 x 2.2
mm
29.
Socket wrench SW 19
30.
Installation wrench
31.
PRCD (residual-current-operated circuit
breaker)
32.
Rear flange
33.
Safety label
34.
Hexagon nut M 12 LH
f
d
e
v
i
c
e
/
s
p
a
r
e
p
a
r
t
s
f
d
e
v
i
c
e
/
s
p
a
r
e
p
a
r
t
Bestell.-Nr.
344702
364733
364734
364703
364704
364705
364706
364707
364735
364710
364712
364713
364714
364715
364716
364725
364717
364719
364720
364718
364736
391672
390908
364730
364721
364723
364722
364041
364731
364010
364732
s
16
Werbung
Kapitel
Inhaltsverzeichnis
