Technical Data; Brief Description; Operation - Felisatti RSF120/1010E Bedienungsanleitung

CHARACTERISTICS
Cutting capacity, max.
– in wood, mm
– in non-alloy steel, mm
Run-out, mm
Rated power input, W
Voltage, V
Frequency, Hz
Stroke rate at no load, min
Weight according EPTA-Procedure 01/2003, kg
Sound pressure level, dB(A)
Sound power level, dB(A)
Protection class
The instructions contained in this manual must be strictly
followed, it should be carefully read and kept close at hand to
use when carrying out maintenance on the indicated parts.
If the tool is used with care and normal maintenance is carried
out, it will work well for a long time.
The functions and use of the tool you have bought shall be
only those described in this manual.
Any other use of the tool is strictly forbidden.
See safety regulations attached to this statement.
ILLUSTRATIONS
Description (See figures)
1 Saw blade
2 Adjustable footplate
3 Saw blade holder
4 Locking sleeve for saw blade
5 On/Off switch
6 Lock-off button for On/Off switch
7 Handle (insulated gripping surface)
8 Lever
9 Constant electronic speed regulation

BRIEF DESCRIPTION

The machine is intended for sawing wood, plastic, metal
and building materials while resting firmly on the workpiece.
It is suitable for straight and curved cuts. When using the
appropriate bimetal saw blades, it is possible to cut flush to the
workpiece surface. The saw blade recommendations must be
observed. Use only ½" universal shank saw blades. The saw
blade should not be longer than required for the intended cut.
BEFORE USING THIS TOOL
Before using the tool, make sure the mains voltage is
correct: it must be the same as that on the specification
label. Machines with 230 V can also be connected to a 220
V mains supply. Before plugging the tool in, always check
that On/Off switch is functioning normally and returns to Off
when released.
REPLASING/INSERTING THE SAW BLADE
Inserting the Saw Blade
Turn the locking sleeve 4 approx. 90° in the direction of the
4

TECHNICAL DATA

-1
RSF120/1010E
220±10%
50±5%
300-2500
arrow and hold. Push the saw blade 1 into the saw blade
holder 3. Release the locking sleeve 4 again. Check the
tight seating of the saw blade. A loose saw blade can fall
out and lead to injuries. For certain work, the saw blade 1 can
also be turned through 180° (with the teeth pointed upwards)
and re-inserted again.
Removing the Saw Blade
Turn the locking sleeve 4 approx. 90° in the direction of the
arrow and hold. Remove the saw blade 1.

OPERATION

Pivoting and Retractable Footplate
Due to its movability, the adjustable footplate 2 adapts to the
required angular position of the surface. Depending on the
saw blade being used and the application, the footplate 2 can
be moved in lengthway direction in three steps.
Move the lever for the footplate 8 and slide the footplate 2
to the required position. Move the footplate lever 8 to initial
position.
Starting the tool
WARNING! Plug the machine in with the switch off.
Pressing On/Off switch will turn the machine on and
releasing it will turn it off again. For continuous operation,
press On/Off switch and lock it in the operating position
using button retainer B. If the On/Off switch is depressed and
released once again, the machine will stop.
Speed regulation
Regulator 9 is located in the upper section of the handle.
Regulator 9 is used to set the required speed. Position A
corresponds to the minimum speed and position F is the
maximum speed.
Electronic regulation can be carried out with the machine
running.
The optimum number of strokes depends on the material and
particularly on the working conditions. The table below allows
to choose optimal speed for various types of materials.
Materials
Wood
Steel
Alloy steel
Aluminum
Plastic
250
120
28
1010
3,8
93
104
II
Position of speed regulator
D-F
C-E
C-D
C-F
A-D