Technical Data; Brief Description - Felisatti SCF 190/1600 Bedienungsanleitung

Circular saws
Input power
No-load speed
Saw blade diameter
Max./min. saw blade diameter
Max./min. set width
Saw blade hole diameter
Depth of cut at 90°
Depth of cut at °
Depth setting
Inclination setting
Approx. weight (w/o
accessories) according
EPTAProcedure 01/00
Follow very carefully the instructions in this manual, save it
and keep it close at hand, ready to carry out any inspection
of parts that may be necessary.
If the tool is used with care and normal maintenance is carried
out, it will work well for a long time.
The functions and use of the tool you have bought shall be
only those described in this manual. Any other use of the
tool is strictly forbidden.
ILLUSTRATIONS
DESCRIPTION (See figures)
A HM saw blade. (Fig. 1)
B Riving knife setting screw (Fig. 1)
C Mobile blade guard (Fig. 1)
D Saw blade setting disc (Fig. 1)
E Disc setting screw (Fig. 1)
F Riving knife (Fig. 1)
G Depth setting wing nut (Fig. )
H Lateral stop setting wing nut (Fig. )
I Lateral stop (Fig. 1)
J Safety push button switch (Fig. )
K On-/off switch (Fig. )
M Cutting line guide (Fig.)
N Sawdust extraction (Fig. 1)
EQUIPMENT
- 1 lateral stop
- 1 disc clamping key
- Operating instructions
- Safety instructions
- Warranty

BRIEF DESCRIPTION

This tool is specially designed for straight sawing only of
boards made from wood and derivatives (plywood, chipboard
etc.).
BEFORE USING THIS TOOL
Before using the tool, make sure the mains voltage is correct:
it must be the same as that on the specification label.

TECHNICAL DATA

SCF165/1200
W 100
rpm 700
mm 16
mm 16/160
mm ,
mm 0
mm 
mm 7
mm 0-
0-°
Kg. ,
SCF190/1600S SCF210/1900S
1600 1900
800 000
190 10
190/180 10/00
, ,
0 0
6 7
 1
0-6 0-7
0-° 0-°
,6 6,
Machines with 0V can also be connected to a 0V mains
supply.
Before plugging in the tool, always make sure the control
switch K works properly and returns to the OFF position
when released.
START UP
WARNING! Only plug in when machine is switched off.
Press the locking button J, and squeeze the trigger in the on/
off switch K. When the on/off switch is released, the machine
stops.
CONSTANT ELECTRONICS (SCF210/1900VES)
The built-in module permits:
- Soft start.
- The maintenance of a practically constant rated speed
up to rated power.
Overload protection
- The motor will stop if an overload occurs. The machine
should be immediately removed from the piece being worked
and allowed to operate off-load at maximum revolutions
during some thirty seconds in order to cool the motor.
FITTING THE DISC
WARNING! Always unplug the machine before carrying out
any work on it.
CAUTION: Do not use bent or cracked blades or high-speed
steel blades. Do not use saw blades that do not conform to
the specifications contained in these instructions.
1. Move the mobile guard C backwards and hold it in
place.
. To loosen or tighten the screw E with the key supplied with
the machine, secure the blade with the aid of a screwdriver
as follows: turn the blade guard to the side and turn the blade
until the hole lies under the saw shoe and insert a screwdriver
in the hole so that the blae does not move (or place the saw
on a piece of wood).
. Loosen the screw E and remove the setting disc D.
. Fit the saw blade and tighten with the setting disc D and
the screw E.
5. Before fitting the new blade, make sure the surfaces in
contact with the setting discs are clean. The teeth of the saw
should protrude beyond the riving knife F. (The arrow printed
SCF210/1900VES
1900
00-000
10
10/00
,
0
7
1
0-7
0-°
7,8