Bosch GNA 3,5 Professional Originalbetriebsanleitung Seite 10

10 | English
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Screw for handle holder
(2) Handle holder
(3) Auxiliary handle
(4) Hex key
(5) On/off switch
(6) Thread for auxiliary handle
(7) Screw for punch fastener
(8) Hole on die holder
(9) Screw for die
(10) Punch
(11) Guide plate
(12) Hold-down device
(13) Screw for hold-down device
(14) Die
(15) Die holder
(16) Punch positioner
Technical Data
Nibbler
Article number
Rated power input
Power output
No-load stroke rate n
0
Stroke speed under load
Max. sheet thickness that
A)
can be cut
Cutting track width
Min. curve radius
Weight according to
EPTA-Procedure 01:2014
Protection class
A) with reference to steel sheet of up to 400 N/mm
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Noise/Vibration Information
Noise emission values determined according to
EN 62841‑2‑8.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 83 dB(A); sound power level
94 dB(A). Uncertainty K = 3 dB.
Wear hearing protection
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841‑2‑8:
2 2
a = 9 m/s , K = 1.5 m/s .
h
1 609 92A 505 | (24.06.2019)
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
Auxiliary handle
Screw the auxiliary handle (3) into the thread (6) on the left-
GNA 3,5
or right-hand side of the housing.
0 601 533 1..
You can use the handle holder (2) to extend the auxiliary
W 620
handle and reposition it at any angle for a safe work posture
W 340
that minimises fatigue.
−1
min 1000
If the auxiliary handle is already fitted, unscrew it from the
thread (6). Use the screw (1) to screw the handle holder (2)
−1
min 670
in the thread at the required angle on the left- or right-hand
mm 3.5
side of the housing. Screw the auxiliary handle into the nar-
rower end of the handle holder on the left- or right-hand side
mm 6
accordingly.
mm 70 If you attach the handle holder on the left-hand side of the
housing, make sure that it does not cover the on/off
kg 3.5
switch (5).
/Ⅱ
Operation
2
u
Starting Operation
u
Adjusting the hold-down device
Adjusting the hold-down device (12) to the thickness of the
sheet being cut eliminates vibrations.
Hold the power tool so that the die (14) touches the under-
side of the sheet to be cut. Loosen the screws (13) on the
Products that are only sold in AUS and NZ: Use a resid-
ual current device (RCD) with a nominal residual current
of 30 mA or less.
Pay attention to the mains voltage. The voltage of the
power source must match the voltage specified on the
rating plate of the power tool. Power tools marked
with 230 V can also be operated with 220 V.
Bosch Power Tools