Peg Perego CHOO CHOO express train Gebrauch Und Wartung Seite 8

RULES FOR SAFE DRIVING
For the safety of the child, before starting up the
vehicle read and carefully follow the following
instructions.
• Teach the child how to use the vehicle properly for
safe and enjoyable driving.
• Before starting, check that there are no people or
objects obstructing the vehicle's path.
• Drive with hands on the handlebars/steering wheel
and always watch the road ahead.
• Brake in good time to avoid collisions.
2nd GEAR (if present)
Initially, use in 1st gear is recommended. Before
enabling 2nd gear, check that the child has learned to
use the handlebars/steering wheel, 1st gear and the
brake correctly, and has become familiar with the
vehicle.
WARNING!
• Check that all the wheel fixing studs/nuts are
fastened properly.
• If the vehicle is overloaded, as can happen on soft
sand, mud, or very uneven ground, the overload
switch will immediately disconnect the power. The
power supply will be restored after a few seconds..
• Only for 12 and 24 Volt vehicles: in first gear the
vehicle has a differential effect like a real motor
vehicle; on smooth terrain and with just one child
on board, the two wheels can turn at different
speeds and they can slip and slow down.
UNINTERRUPTED FUN: Keep a spare set of charged
batteries ready for use.
PROBLEMS?
THE VEHICLE DOES NOT WORK?
• Check that there are no disconnected cables under
the accelerator plate.
• Check the operation of the accelerator button and
replace it if necessary.
• Check that the battery is connected to the
electrical system.
THE VEHICLE LACKS POWER?
• Charge the batteries. If after charging the problem
persists, have the battery and charger checked by
an assistance centre.
ASSISTANCE SERVICE
offers an after-sales assistance service,
PEG PEREGO
directly or through a network of authorized
assistance centres, for any repairs or replacements
and the sale of original spare parts. To contact the
assistance centres refer to the "Assistance Centres"
booklet included in the packaging.
Peg Perego always strive to best satisfy their
customers' needs. Knowing the opinions of our
customers is therefore very important and valuable
to us. We would be very grateful if, once you have
used the product, you would fill out the
which you can find on
SATISFACTION QUESTIONNAIRE
the internet at: www.pegperego.com, making
any observations or suggestions you might have.
ASSEMBLY INSTRUCTIONS
WARNING
ASSEMBLY MUST ONLY BE CARRIED OUT BY
ADULTS. TAKE CARE WHEN REMOVING THE
VEHICLE FROM ITS PACKAGING. ALL THE
SCREWS AND SMALL PARTS ARE CONTAINED IN
A BAG INSIDE THE PACKAGING. THE BATTERY
MAY ALREADY BE FITTED INSIDE THE ITEM.
1 • Snap-fit the end of the funnel, which is included
in the packaging.
2 • Loosen the screw on the front of the seat.
3 • Remove the seat by lifting the front part (1) and
pulling out the back part (2).
4 • Remove the battery charger from the
compartment under the seat.
5 • Connect the battery plug (A) to the system plug
(B).
6 • Put the seat back into place, inserting the back
part first (1) and then the front part (2).
7 • Fasten the seat with the screw. The vehicle is
ready for use.
8 • The product can operate both with and without
the track. Assemble the track as shown in the
figure. For best results, position the train on the
track so that it travels anticlockwise.
9 • To use the train off the track, remove the screw
on the coupling lock as shown in the figure.
10 • Turn the lock around and put it back, as shown
in detail A of the figure. Secure the lock with the
screw. To use the product on the track again, it is
necessary to return it to its original state.
FEATURES AND USE OF THE VEHICLE
11 • OPERATION BUTTONS: Press button A to play
the tunes. Press the button again to change the
tune. To start the train, press button B: the
headlight and the sound effects will also
automatically come on.
12 • ARMRESTS: Pull the seat out as shown above.
Unhook and remove the armrests (see figure).
Put the seat back into place and fasten it with
the screw.
13 • FIGURE 8 TRACK: The kit for the Figure 8 Track
includes 6 bends, 4 straight pieces of track, and 4
intersections. By adding the 12 bends that come
with the train, the track will make a figure eight.
14 • When you purchase a FIGURE 8 TRACK, you
can also make the OVAL FIGURE using the 4
pieces of straight track.
15 • To assemble the FIGURE 8 TRACK, place a piece
of intersection over another piece, as shown in
the figure.
16 • Add a second piece of track.
17 • To fasten the last piece of the intersection, turn
the first and last piece slightly, as shown in the
figure.
18 • Complete the track by adding the remaining
pieces.
REPLACING THE BATTERY
19 • Remove the seat. Loosen the screw and remove
the fake coal from the back of the seat.
20 • Loosen the 2 screws on the battery clamp.
Disconnect the battery and the system plugs.
21 • Replace the battery (NOTE: The spare battery
must be purchased separately and must be a 6-
Volt/8Ah Peg Perego Original battery).
22 • Put the battery back into place and fasten the
screws. Reconnect the two plugs.
23 • Put the fake coal back into place.
24 • Fasten the fake coal with the screw and put the
seat back into place, as shown above. Fasten the
seat with the screw.
CHARGING THE BATTERY
WARNING: BATTERY CHARGING AND EVERY
OTHER OPERATION ON THE ELECTRICAL
SYSTEM MUST BE CARRIED OUT BY ADULTS
ONLY.
THE BATTERY CAN ALSO BE CHARGED
WITHOUT REMOVING IT FROM THE TOY.
25 • Disconnect plug A (the electrical system plug)
from plug B (the battery plug) by pressing on the
sides of the plugs.
26 • Connect plug B to plug C (the battery charger
CONSUMER
plug). Connect the battery charger to a
household electrical outlet, following the
instructions supplied with the battery charger.
27 • When the battery is completely charged,
ASSEMBLY
OPTION
disconnect the battery charger from the outlet
and disconnect plug C from plug B.
28 • Connect plug B to plug A, pressing until it clicks
into place.
29 • Always remember to put the seat back into
place and to fasten it with a screw.