Specifications; Standard Accessories; Prior To Operation - Hitachi D 13T2 Bedienungsanleitung

English

SPECIFICATIONS

Model
Voltage (by areas)*
Power input
Speed change
No load speed
Steel
Capacity
Wood
Weight (without cord)
Spec. for chuck fitted with chuck wrench
Spec. for keyless chuck
*Be sure to check the nameplate on product as it is subject to change by areas.

STANDARD ACCESSORIES

(1) Chuck Wrench (Spec. only for chuck fitted with
chuck wrench) ........................................................... 1
(2) Side Handle ............................................................... 1
(3) Depth Gauge ............................................................. 1
Standard accessories are subject to change without no-
tice.
OPTIONAL ACCESSORIES (sold separately)
Drill Stand (Model D10–DS)
Optional accessories are subject to change without no-
tice.
APPLICATIONS
Boring holes in metal, wood and plastic.

PRIOR TO OPERATION

1. Power source
Ensure that the power source to be utilized con-
forms to the power requirements specified on the
product nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the
power switch is in the ON position, the power tool
will start operating immediately, inviting serious
accident.
3. Extension cord
When the work area is removed from the power
source. Use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4. Mounting and dismounting of the bit.
For Drill chuck with chuck wrench
Fit the drill bit into the chuck and use the chuck
wrench to secure it, tightening the chuck by each
of the three holes in turn.
5
D13VB2
(110V, 115V, 120V, 127V, 220V, 230V, 240V)
1
0–1100/min
13 mm
40 mm
For keyless chuck
(1) Mounting the bit
Turn the lock collar in the direction "AUF" and open
the chuck. After Inserting the drill bit Into the chuck
as far it will go, turn the lock collar in the "ZU"
direction. Grip the retaining ring and close the chuck
by turning the sleeve clockwise as viewed from the
front.
(2) Dismounting the bit
Turn the lock collar in the direction "AUF" to release
the shucking force. Grip the retaining ring and open
the chuck by turning the sleeve counterclockwise.
NOTE
When the sleeve does not become loose any fur-
ther, fix the side handle to retaining ring, hold side
handle firmly, then turn the sleeve to loosen by
hand. (Fig. 4)
5. Selecting the appropriate drill bit
When boring metal or plastic
Use an ordinary metalworking drill bit.
When boring wood
Use an ordinary woodworking drill bit.
However, when drilling 6.5 mm or smaller holes,
use a metalworking drill bit.
6. Confirm the direction of bit rotation (Fig. 5)
The bit rotates clockwise (viewed from the rear
side) by pushing the R-side of the reversing switch
lever. The L-side of the lever is pushed to turn the
bit counterclockwise. (for D13VB2 only)
7. Fixing the side handle (Fig. 6)
Loosen the wing bolt on the side handle, and attach
the side handle to the gear cover in a position
convenient for drilling. Match the projecting part of
the handle to the groove on the gear cover, and
firmly tighten the wing bolt. To remove the side
handle, loosen the wing bolt and rotate the handle.
To attach a depth gauge on the side handle, insert
the gauge into the U-shaped groove on the side
handle, adjust the position of the depth gauge in
accordance with the desired depth of the hole, and
(Fig. 1)
firmly tighten the wing bolt.
8. High-spped/Low-speed changeover
To change speed, rotate the gear shift dial as
indicated by the arrow in Fig. 7. The numeral "1"
engraved on the drill body denotes low speed, the
750W*
2 1
0–2600/min 1100/min
8 mm 13 mm
25 mm 40 mm
2.1 kg
2.3 kg
(Fig. 2, 3)
D13T2
2
2600/min
8 mm
25 mm