Before Starting The Equipment - EINHELL RT-RH 26 Originalbetriebsanleitung

Anleitung_RT_RH_26_SPK7__ 23.10.12 07:18 Seite 14
GB
Hammer drilling in concrete
Vibration emission value a = 17.5 m/s
h
K uncertainty = 1.5 m/s 2
Chiseling
Vibration emission value a = 16.352 m/s
h
K uncertainty = 1.5 m/s 2
Additional information for electric power tools
Warning!
The specified vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equipment
is used and may exceed the specified value in
exceptional circumstances.
The specified vibration value can be used to compare
the equipment with other electric power tools.
The specified vibration value can be used for initial
assessment of a harmful effect.
Keep the noise emissions and vibrations to a
minimum.
Vibration values exceeding 2.5 m/s
n
damage to the joints in your hand and arm.
Only use appliances which are in perfect working
n
order.
Service and clean the appliance regularly.
n
Adapt your working style to suit the appliance.
n
Do not overload the appliance.
n
Have the appliance serviced whenever
n
necessary.
Switch the appliance off when it is not in use.
n
Wear protective gloves.
n
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain residual
risks cannot be rules out. The following hazards
may arise in connection with the equipment's
construction and layout:
1. Lung damage if no suitable protective dust mask
is used.
2. Damage to hearing if no suitable ear protection is
used.
3. Health damage caused by hand-arm vibrations if
the equipment is used over a prolonged period or
is not properly guided and maintained.
14

6. Before starting the equipment

2
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
2
Always pull the power plug before making
adjustments to the equipment.
Check the drilling point for concealed electrical
cables, gas and water pipes using a cable/pipe
detector.
6.1 Additional handle (Fig. 2 – Item 6)
For safety reasons you must only use the
hammer drill with the additional handle.
The additional handle (6) enables you to achieve
better stability whilst using the equipment. Do not use
the equipment without the additional handle.
The additional handle (6) is secured to the equipment
by a clamp. Turning the handle clockwise tightens this
clamp. Turning it anti-clockwise will release the clamp.
The supplied additional handle (6) must first be
n
fitted. To do this, turn the handle until the clamp is
opened wide enough for you to slide the
additional handle onto the equipment.
2
may cause
After you have mounted the additional handle (6),
n
swivel it to the most comfortable working position
for yourself.
Now turn the handle in the opposite direction
n
again until the additional handle is secure.
The additional handle (6) is suitable for both left-
n
handed and right-handed users.
6.2 Depth stop (Fig. 3 – Item 7)
The depth stop (7) is held in place with the locking
screw (10) on the additional handle (6) by means of
a clamp.
Undo the locking screw (10) and fit the depth
n
stop (7).
Set the depth stop (7) to the same level as the
n
drill bit.
Pull the depth stop (7) back by the required
n
drilling depth.
Retighten the locking screw (10).
n
Now drill the hole until the depth stop (7) touches
n
the workpiece.
6.3. Tool insertion (Fig. 4)
Clean the tool before insertion and apply a thin
n
coating of drill bit grease to the shaft of the tool.
Pull back and hold the locking sleeve (2).
n
Insert the dust-free tool into the tool mounting as
n
far as it will go whilst turning it. The tool will lock
itself.
Check that it is properly secure by pulling the
n