Product Description; Electrical Connections; Motor Connection; Power Supply - Nice mindy TT1V Anweisungen Und Hinweise Für Den Installateur

Warnings
The TT1V control unit is suitable for the control of a single-phase asyn-
chronous motor powered by the electrical mains and used for the
automation of venetian blinds.

1) Product description

The TT1V control unit enables the control of a single-phase asyn-
chronous motor powered by the electrical mains, with "COMMON"
"UP" "DOWN" type connections, and used for the automation of
venetian blinds.
The control unit incorporates a radio receiver operating at a frequen-
cy of 433.92 MHz, with rolling code technology that guarantees high
levels of security. Up to 30 transmitters ("ERGO" fig. 1, "PLANO" fig.
2) or radio-controlled sensors ("VOLO S RADIO" fig. 3) can be mem-
orized for each control unit. "Man present" mode will function for the
first 2÷ 3 seconds after a command on the transmitter is pressed.
This enables the user to swivel the blades of the Venetian blind as
necessary. Once this time has elapsed, the command will activate
the motor in semiautomatic mode and complete the ascent or
descent manoeuvre. "VOLO S RADIO" climatic sensors (Fig. 3)
enable users to manage the movement of the venetian blinds auto-
matically, depending on the wind, sun or rain conditions.
2) Installation
!
The electrical systems and automations must be installed by
qualified and experienced personnel in compliance with current
legislation. Before you proceed to make any connections make
sure that the power supply is disconnected.
1. Strip the motor cable and the power supply cable about 3 cm
and then the single wires approx. 5 mm.
2. Open the container by removing the "cable cap" as shown in fig. 5.
3. Thread the two cables through the designated holes in the "cable
cap" (see fig. 6).
4. Pull the card a few centimetres out of the container (see fig. 7).
5. Connect the wires to the terminals as shown in fig. 8, observing
the diagram in fig. 4 and the operations described in chapter 2.1.

2.1) Electrical connections

!
Carefully follow all the connection instructions, if you have
any doubts do NOT make experiments but consult the rele-
vant technical specifications sheets which are also available
on the web site www.niceforyou.com
An incorrect connection may cause serious damage to the
control unit.
4

2.1.1) Motor connection

The single-phase asynchronous motor powered by the electrical
mains must be connected on terminals 1-2-3-4 (DOWN, COMMON,
UP, EARTH).
"DOWN" is controlled by the
by the key. (anemometer intervention direction).

2.1.2) Power supply

The main supply to the unit must be connected using the terminals 5-6-7 (earth, phase, neutral) as shown in Fig. 4
2
key on the remote control, and "UP"
Any other use is improper and prohibited. The unit must be installed by
qualified technicians in compliance with the electrical and safety regula-
tions in force.
N.B.: Besides "ERGO", "PLANO" and "VOLO S RADIO", the control
unit can manage other kinds of transmitters and functioning modes,
too. Please refer to Chapter 4 "Additional information" for further
explanations.
1 ERGO 2 PLANO
6. Fold the cables as shown in fig. 9.
7. Push the card inside the container, make sure that the stripped
length of the cable is fully inside the container, then slide the "cap"
until the container closes completely (see fig. 10)
8. The control unit can be fitted directly in the shutter/awning box,
double-sided tape can be used for this. To avoid the risk of water
leaks it should be positioned with the cables towards the bottom
as shown in Fig. 11. Do not place it with the cables towards the
top (Fig. 12).
!
Do not perforate the container.
M
COM
L
N
If the rotation direction is not correct, invert the terminals 1 and 3.
!
do not connect more than one motor to each control unit;
if necessary, use the appropriate expansion cards.
3 VOLO S RADIO
4 3 2 1
5 6 7