Makita SA5040C Bedienungsanleitung Seite 4

ENGLISH (Original instructions)
1-1. Shaft lock
2-1. Slide switch
3-1. Indication lamp
(speed adjusting dial)
4-1. Speed adjusting dial
5-1. Screw
7-1. Abrasive disc
7-2. Pad
7-3. Spindle
10-1. Head cover
10-2. Gear housing
12-1. Wheel guard
12-2. Bearing box
12-3. Screw
13-1. Wheel guard
13-2. Bearing box
13-3. Screw
13-4. Lever
SPECIFICATIONS
Abrasive disc diameter
Wheel diameter
Max. wheel thickness
Rated speed (n) / No load speed (n
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
Noise
The typical A-weighted
according to EN60745:
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB(A)
Explanation of general view
14-1. Screw
14-2. Lever
15-1. Lock nut
15-2. Depressed center wheel
15-3. Inner flange
16-1. Lock nut wrench
16-2. Shaft lock
17-1. Ezynut
17-2. Abrasive wheel
17-3. Inner flange
17-4. Spindle
18-1. Shaft lock
19-1. Arrow
19-2. Notch
21-1. Lock nut
21-2. Flex wheel
21-3. Plastic pad
21-4. Inner flange
Model
Spindle thread
)
0
Overall length
Net weight
Safety class
noise level determined
) : 84 dB(A)
pA
) : 95 dB(A)
WA
(Depending on the optional wheel guard)
ENE048-1
Vibration
ENF002-2
The vibration
determined according to EN60745:
Work mode : disc sanding with anti vibration side grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
ENG905-1
Work mode : disc sanding with normal side grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : surface grinding with anti vibration
side grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
4
22-1. Sanding lock nut
22-2. Abrasive disc
22-3. Rubber pad
23-1. Marking A
23-2. Marking B
23-3. Marking C
23-4. Marking D
25-1. Lock nut
25-2. Abrasive cut-off wheel/diamond
wheel
25-3. Inner flange
25-4. Wheel guard for abrasive cut-off
wheel/diamond wheel
26-1. Wire cup brush
27-1. Wire wheel brush
28-1. Exhaust vent
28-2. Inhalation vent
SA5040C
125 mm
115 mm or 125 mm
6.4 mm
M14
-1
7,800 min
315 mm
2.2 kg
/II
Wear ear protection
total value (tri-axial
2
) : 2.5 m/s
h,DS
2
2
) : 2.5 m/s
h,DS
2
) : 4.0 m/s
h,AG
2
ENG900-1
vector sum)
or less
or less
2