DeWalt DWS520 Anleitung Seite 33

PlunGE cuTS
WARnInG: To avoid kickbacks,
the following in-structions MUST be
observed when plunge cutting:
• P lace the machine onto the guide rail
and release the anti-kickback knob (u)
by turning it anti-clockwise.
• T urn the machine on and slowly press
the saw down onto the set cutting
depth and push forward in the cutting
direction. The cut indicators (t) display
the absolute front and the absolute
rear cutting points of the saw blade
(dia. 165 mm) at maximum cutting
depth and using the guide rail.
• I f kickback happened during the
plunge cut, turn the anti-kickback
knob (u) anti-clockwise to release it
from the rail.
• W hen you have finished the plunge
cut, turn the anti-kickback knob (u)
clockwise into the lock position.
Guide system (fig. 1, 5)
The guide rails, which are available in different
lengths, allow for precise, clean cuts and
simultaneously protect the workpiece surface
against damage.
In conjunction with additional accessories, exact
angled cuts, mitre cuts and fitting work can be
completed with the guide rail system.
Securing the workpiece with clamps ensures a
secure hold and safe working.
The guide clearance of the plunge saw must be very
small for best cutting results and can be set with the
two rail adjusters (j).
1. Release the screw inside the rail adjuster to
adjust the clearance.
2. Adjust the knob until saw locks on rail.
3. Rotate knob back until saw slides easily.
4. Hold the rail adjuster in position and lock the
screw again.
NoTE: aLWaYS readjust the system for use with
other rails.
SPlinTErGuarD
The guide rail is equipped with a splinterguard,
which has to be cut to size before the first use:
IMPoRTaNT: aLWaYS read and follow the guide
system instruction before cutting the splinterguard!
1. Set the speed of the plunge saw to level 5.
2. Place the guide rail on a scrap piece of wood.
3. Set the plunge saw on 5 mm cut depth
4. Place the saw on the rear end of the guide rail.
5. Turn the saw on, press it down to the set
cutting depth and cut the splinterguard along
the full length in one contiuous operation. The
edge of the splinterguard now corresponds
exactly to the cutting edge of the blade.
WARnInG: To reduce the risk of injury,
ALWAYS secure the guide rail (w) with a
clamp (x).
Speed adjustment (fig. 1)
The speed can be regulated between 1750 and
4000/min using the speed wheel (s). This enables
you to optimise the cutting speed to suit the
material. Refer to the following chart for type of
material and speed range.
Type of Material
to be Cut
Solid wood (hard, soft)
Chipboards
Laminated wood, blockboards,
veneered and coated boards
Paper and carton
Wall cutting (fig. 7)
1. Place the plunge saw with the outer guard (v)
on a clean, flat floor.
2. Press the shoe (d) with the front side on the
door against the adjusted depth stop.
Dust extraction (fig. 1)
Your tool is fitted with a dust extraction outlet (i).
WARnInG: ALWAyS connect the
plunge saw to a dust extractor!
WARnInG: ALWAyS use a dust
extraction device designed in
accordance with the relevant regulations
regarding dust emission.
mainTEnancE
Your D WALT power tool has been designed to
e
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARnInG: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-ups
e ngl ish
Speed
Range
3–5
4–5
2–5
1–3
31