Makita 9563H Bedienungsanleitung Seite 3

ENGLISH (Original instructions)
1-1. Shaft lock
2-1. Slide switch
4-1. Wheel guard
4-2. Bearing box
4-3. Screw
5-1. Wheel guard
5-2. Screw
5-3. Bearing box
6-1. Wheel guard
SPECIFICATIONS
Depressed center wheel diameter
Rated speed (n) / No load speed (n
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
Noise
The typical A-weighted noise level determined according
to EN60745:
Model 9564H,9565H
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB(A)
Wear ear protection
Vibration
The vibration total
determined according to EN60745:
Model 9564H
Work mode : surface grinding with normal side grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Explanation of general view
6-2. Bearing box
6-3. Screw
6-4. Lever
7-1. Screw
8-1. Lock nut
8-2. Depressed center grinding
wheel/Multi-disc
8-3. Inner flange
9-1. Lock nut wrench
Model
Spindle thread
)
0
Overall length
Net weight
Safety class
) : 84 dB(A)
pA
) : 95 dB(A)
WA
value (tri-axial vector
2
) : 8.5 m/s
h,AG
2
9563H
100 mm
M10
11,000 min
299 mm
2.1 kg
ENE048-1
Work mode : surface grinding with anti vibration
side grip
Vibration emission (a
ENF002-2
Uncertainty (K) : 1.5 m/s
Model 9565H
Work mode : surface grinding with normal side grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
ENG905-1
Work mode : surface grinding with anti vibration
side grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
The declared vibration emission value has been
•
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
The declared vibration emission value may also be
•
used in a preliminary assessment of exposure.
The declared vibration emission value is used for
•
ENG900-1
main applications of the power tool. However if the
power tool is used for other applications, the
sum)
vibration emission value may be different.
WARNING:
The vibration emission during actual use of the
•
power tool can differ from the declared emission
value depending on the ways in which the tool is
3
9-2. Shaft lock
11-1. Lock nut
11-2. Abrasive cut-off wheel/
diamond wheel
11-3. Inner flange
11-4. Wheel guard for abrasive cut-off
wheel/diamond wheel
12-1. Exhaust vent
12-2. Inhalation vent
9564H
115 mm
M14
-1 -1
11,000 min
299 mm
2.3 kg
/II
) : 8.0 m/s
h,AG
2
) : 9.0 m/s
h,AG
2
) : 7.5 m/s
h,AG
2
9565H
125 mm
M14
-1
11,000 min
299 mm
2.3 kg
2
2
2
ENG902-1