Optional Accessories - Makita DFS441 Bedienungsanleitung

Reversing switch action
► Fig.6: 1. Reversing switch lever
This tool has a reversing switch to change the direction
of rotation. Depress the reversing switch lever from the
A side for clockwise rotation or from the B side for coun-
terclockwise rotation.
When the reversing switch lever is in the neutral posi-
tion, the switch trigger cannot be pulled.
CAUTION:
Always check the direction of rotation
before operation.
CAUTION:
Use the reversing switch only after
the tool comes to a complete stop. Changing the
direction of rotation before the tool stops may dam-
age the tool.
CAUTION:
When not operating the tool, always
set the reversing switch lever to the neutral position.
Depth adjustment
► Fig.7: 1. Locator
The depth can be adjusted by turning the locator. Turn
it in "B" direction for less depth and in "A" direction for
more depth. One full turn of the locator equals 2 mm
change in depth.
► Fig.8: 1. Locator
Adjust the locator so that the distance between the tip
of the locator and the screw head is approximately 3
mm as shown in the figures. Drive a trial screw into your
material or a piece of duplicate material. If the depth is
still not suitable for the screw, continue adjusting until
you obtain the proper depth setting.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
the battery cartridge is removed before carrying
out any work on the tool.
Installing or removing the bit
► Fig.9: 1. Locator
To remove the bit, pull the locator. Then grasp the bit
with a pair of pliers and pull the bit out of the magnetic
bit holder. Sometimes, it helps to wiggle the bit with the
pliers as you pull.
► Fig.10: 1. Locator 2. Bit 3. Magnetic bit holder
To install the bit, push it firmly into the magnetic bit
holder. Then install the locator by pushing it firmly back.
Hook
► Fig.11: 1. Groove 2. Hook 3. Screw
The hook is convenient for temporarily hanging the tool.
This can be installed on either side of the tool.
To install the hook, insert it into a groove in the tool
housing on either side and then secure it with a screw.
To remove, loosen the screw and then take it out.
OPERATION
Screwdriving operation
► Fig.12
Fit the screw on the point of the bit and place the point
of the screw on the surface of the workpiece to be fas-
tened. Apply pressure to the tool and start it. Withdraw
the tool as soon as the clutch cuts in. Then release the
switch trigger.
CAUTION:
• When fitting the screw onto the point of the bit,
be careful not to push in on the screw. If the
screw is pushed in, the clutch will engage and
the screw will rotate suddenly. This could dam-
age a workpiece or cause an injury.
• Make sure that the bit is inserted straight in the
screw head, or the screw and/or bit may be
damaged.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and
the battery cartridge is removed before attempt-
ing to perform inspection or maintenance.
• Never use gasoline, benzine, thinner, alcohol
or the like. Discoloration, deformation or cracks
may result.
To maintain product SAFETY and RELIABILITY,
repairs, carbon brush inspection and replacement, any
other maintenance or adjustment should be performed
by Makita Authorized Service Centers, always using
Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recom-
mended for use with your Makita tool specified
in this manual. The use of any other accessories
or attachments might present a risk of injury to
persons. Only use accessory or attachment for
its stated purpose.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
Center.
• Phillips Insert bits
• Magnetic bit holder
• Various type of Makita genuine batteries and
chargers
• Plastic carrying case
NOTE: Some items in the list may be included in the
tool package as standard accessories. They may
differ from country to country.
7 ENGLISH