Makita KP001G Bedienungsanleitung Seite 16

Installing conventional planer blades
1.
Set a conventional planer blade onto the blade
gauge, aligning its cutting edge along the guide wall on
the blade gauge horizontally.
► Fig.9: 1. Conventional planer blade 2. Blade gauge
3. Cutting edge 4. Guide wall
2. Place the adjusting plate over the conventional
planer blade, and then slightly tighten the screws.
3. Push the adjusting plate forwards until its position-
ing guide neatly and entirely fits along the rear side wall
of the blade gauge.
4. Hold the adjusting plate where it is and tighten the
screws to secure it in place.
► Fig.10: 1. Adjusting plate 2. Conventional planer
blade 3. Screw 4. Positioning guide 5. Rear
side wall 6. Blade gauge
5. Clean out all the wood chips and foreign matters
adhering to the drum and conventional planer blade.
6.
Slip the positioning guide of the adjusting plate
into the guide groove in the drum, and then place the
drum plate over the conventional planer blade (with
adjusting plate).
7. Cross-tighten all the installation bolts evenly with
the box wrench.
► Fig.11: 1. Positioning guide 2. Adjusting plate
3. Guide groove 4. Drum 5. Drum plate
6. Conventional planer blade 7. Installation
bolt
For tool with mini planer blades
NOTE: A pair of planer blades are assembled in
the drum. Repeat the following procedures for each
planer blade.
Removing mini planer blades
1.
Loosen the installation bolts one turn using the
box wrench provided.
► Fig.12: 1. Installation bolt 2. Box wrench
2. Slide the mini planer blade out of the drum by
pushing one end of the blade outwards from the belt
cover side.
► Fig.13: 1. Mini planer blade 2. Drum 3. Belt cover 4.
T-handle of box wrench
NOTE: Use the ends of T-handle of the box wrench to
slide the mini planer blade out for safer operation and
maintenance.
Installing mini planer blades
1.
Clean out all the wood chips and foreign matters
adhering to the drum and mini planer blade.
2. Slide a mini planer blade along between the drum
and set plate by pushing one end of the blade inwards
from the side opposite to the belt cover.
3. Cross-tighten all the installation bolts evenly with
the box wrench.
► Fig.14: 1. Mini planer blade 2. Drum 3. Set plate
4. Belt cover 5. Installation bolt 6. Box
wrench
Mini planer blade calibration
Perform a calibration on planner blades at regular inter-
vals to optimize work efficiency.
1. Loosen the installation bolts one turn using the
box wrench provided.
2. Slide the mini planer blade out of the drum by
pushing one end of the blade outwards from the belt
cover side.
3. Unscrew the installation bolts from the drum using
the box wrench.
4. Disassemble the drum plate and set plate (with
adjusting plate) from the drum.
► Fig.15: 1. Installation bolt 2. Drum plate 3. Set plate
(with adjusting plate) 4. Drum
5. Loosen the screws on the set plate one turn to
disengage the adjusting plate.
► Fig.16: 1. Screws 2. Set plate 3. Adjusting plate
6. Clean out all the wood chips and foreign matters
adhering to the set plate (with adjusting plate) and mini
planer blade.
7. Set the mini planer blade onto the blade gauge,
aligning its cutting edge along the guide wall on the
blade gauge horizontally.
8. Place the set plate (with adjusting plate) over the
mini planer blade, aligning the guide ridges on the set
plate with guide grooves on the mini planer blade.
► Fig.17: 1. Mini planer blade 2. Blade gauge
3. Cutting edge 4. Guide wall 5. Set plate
(with adjusting plate) 6. Guide ridge
7. Guide groove
9.
Push the adjusting plate forwards until its position-
ing guide neatly and entirely fits along the rear side wall
of the blade gauge.
10. Hold the adjusting plate where it is and tighten the
screws to secure it in place.
► Fig.18: 1. Adjusting plate 2. Set plate 3. Screw
4. Positioning guide 5. Rear side wall
6. Blade gauge
11. Slip the positioning guide of the adjusting plate
into the guide groove in the drum, and then place the
drum plate over the set plate (with adjusting plate).
► Fig.19: 1. Positioning guide 2. Adjusting plate
3. Guide groove 4. Drum 5. Drum plate
6. Set plate 7. Installation bolt
12. Slightly tighten the installation bolts, and slide the
mini planer blade along between the drum and set plate
by pushing one end of the blade inwards from the side
opposite to the belt cover.
13. Cross-tighten all the installation bolts evenly with
the box wrench.
► Fig.20: 1. Mini planer blade 2. Drum 3. Set plate
4. Belt cover 5. Installation bolt 6. Box
wrench
16 ENGLISH