Installation Requirements; Radio Frequency Radiation Exposure Information (For Canada And Us Only); Wireless Connection; Pairing With Mi 301 - Grundfos MI 301 Montage- Und Betriebsanleitung

3. Installation requirements

The product must be used as described in these
installation and operating instructions and may not be co-
located or used in conjunction with any other antenna or
transmitter.
3.1 EU
The radio part of this product can be operated in the EU without
restrictions.
3.2 Radio frequency radiation exposure information (for
Canada and US only)
This equipment complies with FCC and Canadian radiation
exposure limits set forth for an uncontrolled environment. This
transmitter must not be co-located or operated in conjunction with
any other antenna or transmitter.
3.2.1 USA
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
Users are cautioned that changes or modifications not expressly
approved by Grundfos could void the user's authority to operate the
equipment.
3.2.2 Canada
CAN ICES-003(B) / NMB-003(B)
This device contains licence-exempt transmitter(s)/receiver(s) that
comply with Innovation, Science and Economic Development
Canada's licence-exempt RSS(s). Operation is subject to the
following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference
that may cause undesired operation of the device.
8

4. Wireless connection

4.1 Pairing with MI 301

To use MI 301 with your smartphone, you must first pair them.
1. Open the main menu in the upper left corner of Grundfos GO
Remote.
2. For iOS smartphones, select Remote > Connect and follow on-
screen instructions.
3. For Android smartphones, select Settings > Remote > Pair
with MI and follow on-screen instructions.

4.2 Grundfos GO Remote

2
3
4
5
1
6
Connecting to a Grundfos product
Pos. Action
Check that your mobile interface has been
1
connected.
2 Press or slide to open or close the menu.
Radio - List: Search for radio-enabled Grundfos
3
products within range.
Radio - Connect: Connect directly to a specific
4
Grundfos product via radio.
IR - Connect: Connect directly to a specific
5
Grundfos product via infrared signal.
6 Press Help for on-screen guidance.
Link to MI 301 quick guide
Related information
2.4 Supported Grundfos products
4.3 Radio connection
4.4 IR connection
4.2.1 Connecting to Grundfos GO Remote
Before connecting the product, the Grundfos GO Remote app must
be downloaded to your smartphone. The app is free of charge and
available for iOS and Android smartphones.
1. Open Grundfos GO Remote on your smartphone. Make sure
that Bluetooth is enabled.
Make sure that your smartphone and MI 301 are charged.
Your smartphone and MI 301 must be within range of each other
to establish Bluetooth connection.
2. Switch on MI 301 by pressing its power button. The indicator
light will flash blue, indicating that MI 301 is ready for
connection.
3. Press the connect icon in Grundfos GO Remote.