Kinderkraft EVERYDAY Bedienungsanleitung Seite 32

NOTE! Before using the buggy make sure that all the wheels are
properly installed.
IV USING THE BRAKE The stroller is equipped with a foot brake. Press the brake with your foot. The brake is activated when
you hear the lock sound. The brake is released when the brake lock is raised (Fig.C).
V. ASSEMBLY/DISASSEMBLY
V.I PRAM BODY Place the nacelle on a flat surface. To unfold the nacelle, remove the foot cover and unfold the nacelle to
the correct size (Fig.D.I, D.II), pull out the mattress in the middle and then, pulling on the strap, mount the front bar until it
locks. Repeat this step to install the rear bar (Fig. E). Place the adapters (16) in the sides of the nacelle, attaching them until
you hear a characteristic click (Fig.F). Make sure that no material gets inside during assembly, then it will not be possible to
place the adapters properly. Place the supplied mattress on top of the prepared element. To fold the nacelle, repeat the
operation in the reverse order. Using the folding and unfolding buttons on both sides of the nacelle's roof, you can adjust
the position of the roof (Fig.G). The canopy must be stretched over the nacelle and fastened with Velcro fasteners. It is
possible to extend the canopy and remove the ventilation panel using the locks on the canopy. Place the cover on the legs
and fasten it with a lock. The foot cover is equipped with an additional wind protection panel, which can be mounted with
a tension device. The rainscreen should be put on the nacelle and secured with Velcro (Fig.H), the mosquito net should be
stretched on the nacelle and secured with straps, the sunscreen should be put on the nacelle and secured with tension on
both sides of the stroller and with straps on the bottom of the nacelle (Fig.I).
V.II ATTACHING THE PRAM BODY TO THE BUGGY FRAME
NOTE! THE PRAM BODY CAN ONLY BE MOUNTED FACING
BACKWARDS (the child faces the person pushing the buggy).
To mount the nacelle, slide it onto the frame of the stroller until the characteristic click (Fig.J). While removing the nacelle,
lift the nacelle release lever from the frame on both sides and pull it up (Fig.K) .
NOTE! Do not fold the buggy frame when the Pram body is
installed on it.
V.III SEAT To mount the seat on the stroller frame, slide it onto the frame as shown in Figure L until it clicks into place. The
seat can be mounted front or rear-facing (Fig. M). To remove the seat, press the buttons on both sides of the seat and lift
up (Fig. M.I). The foot cover must be fastened with the four clip fasteners on each side of the stroller (Fig.N).
V.IV CANOPY
NOTE! INSTALL THE CANOPY BEFORE USING THE BUGGY
Place the canopy in the guide in the seat frame and make sure it is installed correctly (Fig. O). To remove it, press the button
on both sides of the seat frame (Fig.Y) and pull the canopy out. When mounting and dismounting the canopy, remember to
fasten and unfasten the Velcro straps on the top of the canopy and the clips on the sides. The canopy can be adjusted in
several positions.
V.V SAFETY BOW To install the safety bow, slide it into the appropriate guides in the seat frame until it engages (Fig. P). To
remove the component, press the release buttons on both sides of the guide and pull out the safety bow.
VI. SAFETY BELTS Press the button to open the buckle (Fig.R.I). To secure your child, slide the hip and shoulder straps into
the centre buckle until they engage (Fig.R.II).
VII. SEAT POSITIONS The seat has 3 positions: lying, semi-lying and sitting, adjustable by means of the backrest adjustment
lever (Fig.S.I). When the seat is mounted forward facing, the lying position can only be adjusted if the handle bar is extended
in the highest position.
VIII FOOTREST ADJUSTMENT Footrest can be adjusted in one of 4 positions. Press the buttons on both sides of the footrest
at the same time and adjust to the desired position (Fig.S.II).
IX PARENTS HANDLE ADJUSTMENT The stroller handle is adjusted by pressing the button in the middle of the handle and
pulling the handle up or down. You can adjust the handle height to one of 2 levels (Fig.T).
X INSTALLATION OF CUP HOLDER, MOSQUITO NET, RAIN COVER, SUN COVER Fix the cup holder on a pin on the right side
of the stroller frame.
Put the mosquito net on the seat and secure it with the straps at the back of the seat (Fig.U).
Put the rain cover on the stroller and secure with clips (Fig.V).
Put the sun shade on the stroller and secure with clips and straps fastening them under footrest (Fig.W).
XI FOLDING BABY STROLLER Fold the canopy. At the same time, push the release button and pull both folding levers
together to fold the canopy. When the stroller is completely folded, the locking element snaps in (Fig.X). To reduce the size
of the stroller when folded, lower the footrest. You can also set the backrest in the highest position for easy folding of th e
frame. The stroller can be folded with the front or rear-facing seat. The stroller has a standing position when folded, to do
this, lock the front wheels for straight-ahead driving and set the parent's handle in the second position.
32