Cleaning And Maintenance - Concept SR3300 Gebrauchsanweisung

Vorschau ausblenden

Inhalt

Inhaltsverzeichnis

Verfügbare Sprachen

OPERATING INSTRUCTIONS

NOTICE

Always disconnect the plug out of the electrical outlet before assembling or removing accessories! Before putting a new

appliance into operation, you should wipe it thoroughly with a damp cloth and wash all removable parts in warm water

for hygienic reasons.

Never use different adapters at the same time!

Whisks and dough hooks

Whisks are intended for whipping mousse, cream, egg yolks, preparation

of various cremes or runny dough for omelettes and pancakes.

Dough hooks are intended for preparing rubbed, yeast, gingerbread

dough, etc.

The maximum continuous operation time of the appliance (KB) is

5 minutes at speeds 1–5. Then let the appliance cool down for at least

15 minutes.

1. Insert the whisks/whisk or dough hooks into the holes in the bottom

part of the appliance and turn them slightly until they are firmly

attached.

Caution! Insert the whisk or dough hook with ring (Fig. 1) into the larger hole.

2. Unwind the power cord completely. Make sure it does not touch any nearby heat sources. Insert the plug into the

wall outlet.

3. Hold the appliance body with one hand and the whipping/kneading bowl with the other.

4. Insert the whisks/whisk of the appliance (or dough hooks) into the bowl with food and set the required speed. Press

the PULSE button (4) to briefly increase the speed to the maximum.

5. After you have finished whipping/kneading, switch off the appliance. Unplug the power cord from the socket.

6. Press the EJECT button (1) to release the whisks or dough hooks and rinse them immediately under warm running

water.

Caution! When using the appliance, do not touch the walls of the bowl with the whisks/dough hooks. Otherwise,

it could cause a malfunction.

Caution! To prevent overheating, do not let the appliance run for more than 10 minutes. Let the appliance to

cool down to room temperature before restarting it.

Immersion blender

The stick adapter is intended for preparing sauces, toppings, soups, mayonnaise, baby food, mixed drinks and milkshakes.

1. Put food in the blending bowl (F) or any other higher kitchenware.

2. Place the appliance body (A) on the shaft of the stick adapter (E) and turn it to lock it (pull it make sure that the stick

adapter cannot be separated from the body of the appliance).

3. Unwind the power cord completely. Make sure it does not touch any nearby heat sources. Insert the plug into the

wall outlet.

4. Hold the appliance body with one hand (A) and the blending bowl (F) with the other.

5. Move the buttons (3) to the L or H position to set the speed of the appliance. Insert the adapter into the blending

bowl (F) with food and press the PULSE button (4) to switch it on. Blend the food in a circular motion at the bottom

of the bowl.

6. After you have finished blending, switch off the appliance. Unplug the power cord from the socket.

7. Turn and pull to remove the stick adapter from the appliance body and rinse it immediately under warm running

water. Make sure that water does not get into the inside of the adapter to the drive shaft area. If this happens, let

the stick adapter to dry and drip a few drops of edible oil into the drive shaft area to ensure better run of the stick

adapter bearing.

Caution! To prevent overheating, do not let the appliance run for more than 1 minute. Let it cool down to room

temperature before restarting the appliance. Do not let the appliance run idle and do not blend dry food.

Chopper (for SR3310)

Do not chop extremely hard foods such as nutmeg, coffee beans and grains. Cut food such as meat, cheese, onions,

garlic, carrots and frozen foods first. Remove stems from herbs, remove shells from nuts, remove bones, tendons and

cartilage from meat.

Caution! The blades are very sharp, be extremely careful when manipulating with them!

1. Insert blades (H) into the chopping bowl (I) so that they fit on the metal axis.

2. Put the food into the chopping bowl and close it with a transmission lid.

3. Place the appliance body (A) on the transmission lid (G) and turn it to lock it.

4. Unwind the power cord completely. Make sure it does not touch any nearby heat sources. Insert the plug into the

wall outlet.

5. Hold the appliance body with one hand (A) and the chopping bowl (I) with the other.

6. Move the buttons (3) to the L or H position to set the speed of the appliance. Press the PULSE button (4) before

chopping.

7. For better blending results, switch the appliance on and off every few seconds.

8. After you have finished blending, set the speed of the appliance to 0 and switch the appliance off. Turn the appliance

Fig. 1

body (A) and then pull it to remove it from the transmission lid. Unplug the power cord from the socket.

9. Wipe the transmission lid (G) of the chopping bowl with a damp cloth. Do not wash it under running water and do

not immerse it in water!

Caution! To prevent overheating of the appliance, do not let it run for more than 1 minute at a time. Let the

appliance to cool down to room temperature before restarting it.

Caution! When using the hand mixer, do not release the dough hooks / whisks / whisk / blades. Manipulate with

the accessories only after they have stopped moving completely.

Indicative instructions for use

Speed

Blending/mixing

Slow whipping

Blending and whipping

Blending and fast whipping

Blending with immersion blender

PULSE

Chopper