Using The Machine - GGP ITALY SD98 Gebrauchsanweisung

warranty does not cover for damage to plastic
parts of the bodywork or the engine caused by
petrol.
5.3.4 Checking the exit guard (Side dis-
charge chute) (Fig. 5.5)
WARNING! Never use the machine with-
out the exit guards or when the guards are
damaged!
Always check that the inner spring of the chute
(1) works properly, whilst keeping it securely
lowered.
5.3.5 Checking machine safety
and efficiency
1. C heck that the safety devices function as de-
scribed (see 5.2).
2. C heck that the brake is in perfect working
order.
3. D o not start mowing if the cutting means
vibrate or if you are unsure whether they are
sharp enough. Always remember that:
– A badly sharpened cutting means pulls
at the grass and causes the lawn to turn
yellow.
– A loose cutting means causes abnormal
vibrations and can be dangerous.
WARNING! Do not use the machine if
you are unsure whether it is working safely
or efficiently. If in doubt, contact your Dealer
immediately to make the necessary checks
or repairs.

5.4 USING THE MACHINE

5.4.1 Ignition
To start the engine (Fig. 5.6):
– o pen the fuel stopcock (1);
– p ut the transmission into neutral («N»)
(see 4.22 or 4.32);
– d isengage the cutting means (see 4.5);
– a pply the parking brake on sloping ground;
– f or a cold start, use the choke (see 4.2 or
4.2a);
– i f the engine is already warm, just put the lever
between «SLOW» and «FAST»;
– i nsert the ignition key and turn to «ON» to
make electrical contact, then turn to «START»
to start the engine;
– r elease the ignition key once the engine has
started.
When the engine has started, put the accelera-
tor in the «SLOW» position.
All manuals and user guides at all-guides.com
soon as the engine is running smoothly. Using
it when the engine is already warm can foul the
spark plugs and cause the engine to run errati-
cally.
do not insist as you can risk running the battery
flat and flooding the engine. Turn the key to the
«OFF» position, wait for a few seconds and then
repeat the operation. If the malfunction persists,
refer to the engine manual and chapter «8» in
this manual.
safety devices prevent the engine from starting
if safety requirements have not been met (see
5.2). In these cases, once the situation has been
corrected, the key must first be turned back to
«OFF» before the engine can be restarted.
When moving the machine:
– d isengage the cutting means;
– b ring the cutting-means assembly to the high-
– p ut the accelerator control between the
10
IMPORTANT The choke must be closed as
NOTE If there are engine starting problems,
IMPORTANT Always bear in mind that the
5.4.2 Forward gear and riding
without mowing
est position (position «7»);
«SLOW» and «FAST» positions.
Mechanical transmission
Push the pedal down as far as possible (see
4.21) and move the gear change lever into
1st gear (see 4.22).
Keep the pedal pressed down and disen-
gage the parking brake. Slowly release
the pedal which will turn from «brake» to
«clutch», thus operating the rear wheels
(see 4.21).
WARNING! The pedal has to be re-
leased gradually, as a sudden engage-
ment may cause the vehicle to tip over
and the driver to lose control.
Gradually reach the desired speed using
the throttle and gear lever. To change gear,
press the clutch halfway down (see 4.21).
Hydrostatic transmission
Disengage the parking brake and release
the brake pedal (see 4.31).
Press the drive pedal (see 4.32) in direction
«F» and reach the required speed by pro-