Troubleshooting - ROWENTA AIR FORCE RH8657 Gebrauchsanweisung

3 • Turning the vacuum cleaner on
Remove the charger cable from the vacuum
cleaner.
Hold the vacuum cleaner by the handle and
slide the power switch down, to one of the two
following positions (fig.6):
• "Floor": for smooth floors (2.b)
In the «Floor» position, the electrobrush (11.a)
built into the Delta vacuum head, operates at
normal speed.
Note: regularly check that the wheels at the back
of the sucker attachment are clean.
• "Carpet / Booster" : for a better dust pick up
efficiency on all kinds of floors. (2.c)
In the «Carpet» position, the Booster light (3) be-
low the power switch comes on to indicate that
the electrobrush (11.a) is operating at high speed.
Autonomy of your vacuum cleaner * depending
on the position of use:
18 Volts
Lithium
When the appliance is being used, the indicator
light is off.
The indicator light flashes quickly to alert you
that the battery is running low.
When the battery is discharged, to avoid
damage, a security system (automatic 'Cut
Off') stops the appliance and the indicator light
continues to flash for a few seconds. In this case,
put the On/off switch to 0 and put the appliance
in to charge.
USE OF THE ELECTROBRUSH
The Electrobrush is a motorised rotating brush
that ensures very effective cleaning. It vacuums
and cleans deep down. It has bristles all along,
enabling it to remove threads and animal hair
embedded in rugs and carpets.
Note: If the sucker attachment adheres to the
surface too much, place the switch back to the
«Floor» position.
ATTENTION Do not vacuum large debris that
may block the brush and damage it.
Do not use the electro-brush on deep pile car-
pets, animal fur and curtain fringes.
* Depending on model
Position 1 Position 2
« Floor » « Carpet/
Booster »
up to 40 up to 30
MIN MIN
CLEANING THE ELECTROBRUSH
ATTENTION Always stop and unplug your va-
cuum cleaner before maintenance or cleaning.
Delicately cut the threads, hairs, animal fur, etc.
following the notch designed for this
purpose on the electrobrush (fig.7).
FOR YOUR SECURITY
• Do not touch the rotating parts without having
stopped and unplugged the vacuum cleaner.
• Do not use the vacuum cleaner on a wet surface.
• Never immerse your appliance in water.

TROUBLESHOOTING

The electrobrush is working less efficiently or is
making an abnormal noise
• The rotating brush or the hose are clogged:
stop the vacuum cleaner and clean them.
• The brush is worn: please contact an Authorised
Service Centre to have the brush changed.
• The belt is worn: please contact an Authorised
Service Centre to have the belt changed.
The electrobrush stops in the middle of vacuuming
• The heat safety device has come on: stop the
vacuum cleaner by moving the switch to the OFF
position (2.a) and unplug it. Make sure that no-
thing is impeding the rotation of the brush, if so
remove the obstacle and clean the electrobrush
(fig.7), then turn the vacuum cleaner back on.
The electrobrush is difficult to move
• The suction power is too high: reduce the suc-
tion power by moving the switch to the «Floor»
position (2b).
If the problem persists, take your vacuum cleaner
to the nearest Rowenta Approved Service Centre.
See the list of Rowenta Authorised Service
Centres or contact the Rowenta Consumer
Service.
4 • Storage
After use, switch off your vacuum cleaner by
moving the switch to the OFF position (2a). Your
vacuum cleaner may then be put away standing
vertically wherever you want, in its parking
position.
To place the vacuum cleaner in its parking posi-
tion: stand it vertically so as to lock it (Fig. 8)
To use it again: hold the handle and tilt it
backwards to release it from the parking position
(Fig. 9)
12
EN