Useful Information - Atlas Copco P2505 Sicherheits- Und Bedienungsanleitung

Safety and operating instructions
Maintenance
Rust protection and internal cleaning
Water in the compressed air, dust and wear particles
cause rust and sticking of piston, valves etc. This can
be solved by flushing with oil (some drops), running
the machine for 5-10 seconds and absorbing the oil
in a cloth. Make this preparation before longer
standstills.
Overhaul and lubrication
If the machine is normally used as a heavy-duty
machine it should be dismantled, overhauled and
cleaned after 4 months in operation. If the machine
is not running properly, it should be taken out of
service for inspection.
At the overhaul the disassembled parts should be
checked according to the spare parts list. Sliding
parts should be lubricated with oil prior to assembly.
Use lubricants of good quality. The air motor oils
and greases mentioned in the chart are examples of
lubricants which are recommended.
Grease guide
Brand Grease
BP Energrease LS-EP2
Esso Beacon EP2
Q8 Rembrandt EP2
Mobil Mobilegrease XHP 222
Shell Alvania EP2
Texaco Multifak EP2
Molycote BR2 Plus

Useful information

C Log in to Atlas Copco www.atlascopco.com
You can find information concerning our products,
accessories, spare parts and published matters on our
website.
Ergonomic guidelines
) Take frequent breaks and change work positions
1
frequently.
) Adapt the workstation area to your needs and the
2
work task.
• Adjust for convenient reach range by determin-
ing where parts or tools should be located to
avoid static load.
• Use workstation equipment such as tables and
chairs appropriate for the work task.
) Avoid work positions above shoulder level or with
3
static holding during assembly operations.
4
EN
Air lubrication
Energol E46
Arox EP46
Chopin 46
Almo Oil 525
Torcula 32
Aries 32
© Atlas Copco Industrial Technique AB - 9836 0662 02
• When working above shoulder level, reduce
the load on the static muscles by reducing the
weight of the tool, using for example torque
arms, hose reels or weight balancers. You can
also reduce the load on the static muscles by
holding the tool close to the body.
• Make sure to take frequent breaks.
• Avoid extreme arm or wrist postures, particu-
larly for operations requiring a degree of force.
) Adjust for convenient field of vision by minimiz-
4
ing movement of the eyes and head during the
work task.
) Use the appropriate lighting for the work task.
5
) Select the appropriate tool for the work task.
6
) Use ear protection equipment in noisy environ-
7
ments.
) Use high-quality inserted tools or consumables to
8
minimize exposure to excessive levels of vibra-
tions.
) Minimize exposure to reaction forces.
9
• When cutting:
A cut-off wheel can get stuck if the wheel is
either bent or if it is not guided properly. Make
sure to use correct flanges for cut-off wheels
and avoid bending the wheel during cut-off
operation.
• When drilling:
The drill might stall when the drill bit breaks
through. Makes sure you use support handles
if the stall torque is too high. The safety stand-
ard ISO11148 part 3 recommends to use
something to absorb the reaction torque above
10 Nm for pistol grip tools and 4 Nm for
straight tools.
• When using direct driven screw or nutrunners:
Reaction forces depend on tool setting and joint
characteristics. The ability to bear reaction
forces depends on the operator's strength and
posture. Adapt the torque setting to the operat-
or's strength and posture and use a torque arm
or reaction bar if the torque is too high.
) Use dust extraction system or mouth protection
1 0
mask in dusty environments.
Country of origin
Please refer to the information on the product label.
Spare parts
Parts without ordering number are not delivered
separately for technical reasons.
The use of other than genuine Atlas Copco replace-
ment parts may result in decreased tool performance
and increased maintenance and may, at the company
option, invalidate all warranties.
P2505