Black+Decker BHFEA18 Originalanweisungen Seite 9

It does not indicate tool functionality and is subject to variation
based on product components, temperature and end-user
application.
Installing and removing the battery (Fig. D, E)
Warning! Make certain the vac is switched off before
removing or installing battery.
To install battery pack
Insert battery pack (12) into the vac (12c) until an audible
u
click is heard (Figure D). Make sure battery pack is fully
seated and fully latched into position.
To remove battery pack
Depress the battery release button (12d) as shown in
u
Figure E and pull battery pack out of the vac.
Assembly (Fig. F)
Align the top of the extension tube (8) with the vacuum
u
inlet (7a) as shown in Fig. F.
Push the extension tube (8) onto the vacuum inlet (7a) so
u
it locks into position.
To remove an the extension tube, press the extension
u
tube release button (7) and gently pull the extension tube
off.
Warning! When not in use position the unit with the rear of
the vacuum facing a wall so that any inadvertent fall of the unit
would contact a wall and not people or pets.
Useage
This vacuum cleaner can be used in one of two ways.
With the extension tube (8) and the floor head (9).
u
With the crevice tool (11) and the vacuum.
u
Mounting accessories
The crevice tool (11) allows for vacuuming in narrow and
u
hard to-reach places.
To attach the crevice tool (11) press into vacuum inlet (7a)
u
so it locks into position as shown in figure G.
To release the crevice tool (11) press the crevice tool
u
release button (11a) and gently pull the extension tube off.
Switching ON and OFF (Fig. H)
To switch ON, push the on/off power button (1).
u
For increased power, push the On/Off button (1) again.
u
Push the On/Off button (1) a third time to turn the unit off.
u
Note:
The state of charge indicator LEDs (3) will illuminate
while the vacuum is ON.
To switch OFF, slide the on/off power switch (1) to the "O"
u
position.
Charge the battery (12) immediately after use
u
so that it will be ready and fully charged for the next
use.
(Fig. G)
(Original instructions)
Floorsense
Floorsense is active in the low speed. When a carpet is
detected, the performance of the unit is automatically
increased to high speed. When a hardfloor is detected, the
performance of the unit reduces to low speed.
Cleaning and emptying the vacuum
Warning! Projectile/Respiratory Hazard: Never use the vac
without its filter.
Warning! The filter is re-usable, do not confuse it with a
disposable dust bag, and do not throw it away when the
product is emptied. We recommend that you replace the
filter every 6–9 months depending on frequency of use.
To empty the dust canister (Fig. I, J, K, L)
Push down the dust canister release button (4) to
u
release and remove the dust canister (5) from the vacuum.
Use your index finger and thumb to pinch the filter
u
housing tabs and pull the filter housing (6) from the
dust canister as shown in figure I.
Place the dust canister over a trash can and empty the
u
dust canister as illustrated in figure J.
Remove the foam filter (6a) from the filter housing as
u
shown in figure K.
Shake or lightly brush any loose dust off of the foam
u
filter (6a) and filter (6).
Rinse out the dust canister (5) with warm soapy water.
u
Wash the filters with warm soapy water.
u
Ensure the filters are completely dry before refitting the
u
filters into the filter housing.
Refit the clean and dry foam filter (6a) into the filter
u
housing (6).
Install the filter housing into the dust canister (5).
u
Install the dust canister onto the vacuum, until it "clicks"
u
firmly into position.
Removing and cleaning the beater bar
(Fig. M, N)
Warning! To reduce the risk of injury from moving parts,
disconnect the floor head and extension tube from the vacuum
before cleaning or servicing.
To remove the beater bar (9b) from the floor head (9) Slide
u
the beater bar release button (9a) to the rear of the unit.
The beater bar (9b) can now be removed and cleaned.
u
Safe storage (Fig. O)
The unit can be safely stored, when not in use, by placing the
catch on the rear of the motor unit onto the storage station
(13) as shown in figure O.
ENGLISH
9