Flex GDE 10 Originalbetriebsanleitung Seite 14

Overview (Figure A)
1 Sanding head
with brush ring
2 Gimbal bearings
3 Dial for preselecting the speed
4 Locking button
5 Switch
6 Filter cover
7 Slot for battery
8 32 mm connection
9 Flex Li-ion battery
10 Release button for battery
11 State of charge indicator
for connection of electric power tools using conventional
connection piece
12 Suction hose
13 Bail handle (optional)
14 Sanding head DGH-R D150
15 Clamp nut
16 Diamond sanding plate
17 Sanding housing
18 Brush ring DGH-R D150
19 Sanding head DSH-R D150
20 Velcro pad
21 Brush ring DSH-R D150
Instructions for use
WARNING!
Before performing any work on the electric power tool, pull out
the mains plug.
Before switching on the power tool
Unpack the power tool and accessories and check that no parts
are missing. Connect extractor if available (Figure B).
Connect extraction hose to the 32 mm connector.

NOTE
The connection piece of the
electric power tools are used with conventional connection
pieces together with the extraction hose of the
adapter from the FLEX accessories programme can be used.
Attaching/changing the sanding head
(Figure C, D)
WARNING!
Before performing any work on the electric power tool, pull out
the mains plug.
To attach (Figure C):
Press the two locks on the tool change head (1.).

Put the tool change head on the sanding head (2.).

Check that the locking mechanisms have returned to the

home position.
To change (Figure D):
Press the two locks on the tool change head (1.) and remove

sanding head (2.).
14
GDE 10
is a new development.If
GDE 10
Using a dust extraction system
CAUTION!
–
Connect a class M dust extractor when using the renovation
sander.
–
Using a dust bag that is not suitable for the specific dust
generated by sanding can cause an increase in the amount
of dust particles in the air around the workplace. Over a
prolonged period high concentrations of dust in the air may
damage the human respiratory system.
Insert the special dust bag - for the dust generated by sand-

ing - in your power tool according to the instructions sup-
plied with the dust extractor.
Connect extraction hose to the dust extraction system.

Follow the operating instructions for the dust extraction sy-
stem! Check the attachment!
If required, use an appropriate adapter.
NOTE
If your dust extractor requires a special connector, the clip-on
connection can be removed and a matching adapter selected
from the FLEX accessories range.
Attaching and changing the sanding tools
WARNING!
Before performing any work on the electric power tool, pull out
the mains plug.
DSH-R D150 (Figure E)
Remove worn sanding tool from the Velcro pad.

Place the sanding sheet in the centre of the Velcro pad and

press on.
Conduct a test run to check that the sanding tool is clam-

ped in the centre.
CAUTION!
Never use the Velcro pad as a sanding tool. Never use the
renovation sander without the sanding sheet, otherwise the
work surface will be seriously damaged!
DGH-R D150 (Figure F)
Loosen clamping nut by turning it anti-clockwise.

Attach/change diamond sanding pad.

Tighten the clamp nut.

Switch on and off
, an
Brief operation without engaged switch rocker
(Figure G)
First press the starting lockout. Then press and hold down the

switch. Release switch interlock.
To switch off, release the switch.

Continuous operation with engaged switch rocker
(Figure H)
First press and hold down the starting lockout and then the

switch.
To lock into position, hold down the locking button and release

the switch. Release switch interlock.
Figure I
To switch off, briefly press and release the switch.

CAUTION!
Following a power failure, the switched on power tool does not
restart.
GDE 10