Bosch GCM 10 GDJ Professional Originalbetriebsanleitung Seite 36

36 | English
Assembly
Avoid starting the power tool unintentionally. The
u
mains plug must not be connected to the power supply
during assembly or when carrying out any kind of
work on the power tool.
Items Included
See the list of items included at the start of
the operating manual.
Check to ensure that all the parts listed below have been
supplied before using the power tool for the first time:
– Sliding mitre saw with mounted saw blade (34)
– Locking knob (11)
– Clamping handle (13) with fastening set
– Extension bar (16) and clamping lever (18) with fasten-
ing set
– Dust bag (1)
– Hex key (30)
– Screw clamp (19)
Note: Check the power tool for possible damage.
Before continuing to use the power tool, carefully check that
all protective devices or slightly damaged parts are working
perfectly and according to specifications. Check that the
moving parts are working perfectly and without jamming;
check whether any parts are damaged. All parts must be fit-
ted correctly and all the conditions necessary to ensure
smooth operation must be met.
If the protective devices or any parts become damaged, you
must have them properly repaired or replaced by an author-
ised service centre.
Extra tools required (not included in the delivery):
– Cross-headed screwdriver
– Ratchet spanner (size: 8 mm)
– Ring spanner, open-ended spanner or socket spanner
(sizes: 10 mm and 17 mm)
Fitting individual components
– Carefully remove all parts included in the delivery from
their packaging.
– Remove all packing material from the power tool and the
accessories provided.
Fitting the locking knob (see figure a)
– Screw the locking knob (11) into the corresponding hole
above the lever (12).
Always tighten the locking knob (11) firmly before
u
sawing. Otherwise the saw blade can become wedged in
the workpiece.
Fitting the Clamping Handle for Various Bevel Angles
(see figure a)
To fit the clamping handle (13), use the fastening set
provided (socket spanner, nut, two washers).
1 609 92A 6SR | (09.07.2021)
– Place the individual components in the order shown
(large washer, clamping handle, small washer, nut) onto
the threaded bolts on the power tool.
– For better power transfer when tightening the nut, insert
the hex key (30) provided through the holes on the
socket spanner.
– Tighten the nut.
Fitting the Extension Bar (see figure b)
To fit the extension bar (16), use the fastening set provided
(two clamping levers (18), two spring bolts, two knurled
screws).
– Slide the extension bar (16) in as far as it will go into the
corresponding holes in the saw table (33).
– Drive the knurled screws by hand into the corresponding
holes.
– Place the clamping lever (18) on the head of the knurled
screw.
– Fix the clamping lever (18) in place using the spring bolt.
– Increase the clamping force of the clamping lever (18) by
tightening the spring bolts using the hex key (30)
provided.
Stationary or flexible mounting
To ensure safe handling, the power tool must be
u
mounted on a flat, stable work surface (e.g. work
bench) before use.
Mounting on a work surface (see figure c1)
– Use suitable screw fasteners to secure the power tool to
the work surface. The holes (15) are used for this pur-
pose.
or
– Firmly clamp the base of the power tool to the work sur-
face with commercially available screw clamps.
Mounting on a Bosch saw stand
(see figure c2)
(GTA 2500 W, GTA 3700, GTA 3800)
With the height-adjustable legs, Bosch GTA saw stands
provide firm support for the power tool on any surface. The
workpiece supports of the saw stand are used for underlay-
ing long workpieces.
Read all the warnings and instructions included with
u
the saw stand. Failure to observe the warnings and fol-
low instructions may result in electric shock, fire and/or
serious injury.
Assemble the saw stand properly before mounting the
u
power tool. Correct assembly is important to prevent the
risk of collapsing.
– Mount the power tool on the saw stand in the transport
position.
Dust/Chip Extraction
The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
Bosch Power Tools