Safety Instructions - Ultimate Speed Ian 337946 2001 Montage-Und Sicherheitshinweise

Car seat cover set
• Introduction
We congratulate you on your purchase. You have chosen a high quality product.
The instructions for use are to be considered as part of this product. Before using the
product, please familiarise yourself with all the safety information and instructions
for use. Only use the product as instructed and only for the stated areas of use. If you pass the
product on to anyone else, please ensure that you also pass on all the documentation with it.
• Intended use
Set of car seat covers for the driver's seat and passenger's seat (according to the enclosed
type list).

• Safety instructions

Correct installation res. fastening of the seat covers to the vehicle is essential to guarantee the sa-
fety of the user. Please pay attention to the following information when installing the seat covers:
WARNING!
•
ckaging out of reach of small children.
• Installation is permissible only in cars that are indicated in the list of types on the pa-
ckaging or in the enclosed, detailed list of types.
• Headrest inserts, adjustment levers / wheels for release of backrests or armrests may
not be covered with the seat cover. Allowances must be made for appropriate inserts.
Please observe the instructions given in section "Installation".
• Displaced seat covers must be repositioned. If this is no longer possible due to a advan-
ced state of wear and tear, the cover must be removed or replaced.
• Manipulation of the opening of the seat covers is not permissible (no covering, sewing
up or repairs by yourself).
This protective cover has been tested by TÜV Rhineland Group.
CAUTION! If the seat covers are installed incorrectly, the proper extension and infla-
tion of the seat air bag cannot be guaranteed in the case of a collision.
CAUTION! This product can rub off! Do not use on light fabrics and leather!
• Installation of seat covers
You need a pair of pointed scissors.
Important: Please read the information below before installing the seat covers!
Fig. 1: Remove headrests (in some car models the headrests must be dismantled
in a garage).
Fig. 2:
Cover the backrest by pulling the cover downwards.
Fig. 3:
Pull the strap through between the seat and the backrest.
Fig. 4:
Then close the fastener.
Fig. 5: The draw string faces to the front and downward. The rubber bands face
to the rear. Lead the rubber bands of the draw string round the side of the
seat.
Fig. 6: Close the rubber bands of the draw string behind the seat.
Fig. 7:
Fasten the metal hooks under the seat according to the car model (e.g. to
the existing metal rods - ATTENTION Do not fasten to airbag cables!)
ATTENTION!
Openings for backrest releases, adjustment levers, side levers etc. (as described
under fig. 8-14) must be cut out.
If your seat is equipped with armrests, proceed as described
under fig. 8. Otherwise go to fig. 11.
Fig. 8:
Pull the cover down as far as the armrest. The cover must be tightly fitting
on top.
Fig 9:
Cut the cover in the position of the armrest. The cut-out may not be too
large. Push up the armrest and pull it through the cut-out opening of the
cover.
Fig. 10:
Pull the strap through between the seat and the backrest and close with
the fastener.
If your seat is equipped with side levers, proceed as described
under fig. 11. Otherwise go to fig. 13.
Fig. 11:
Cover the seat as described under section 2. The cover must be tightly
fitting on top.
Fig. 12: Cut the cover in the position of the side lever. The cut-out may not be too
large.
Fig. 13:
With the aid of scissors, push the cover under the guide fitting.
GB/IE 6
DANGER OF SUFFOCATION! Keep the pa-
If your seat is equipped with seat frame cladding, proceed as
described under fig. 14. Otherwise go to fig. 14.
Fig. 14: (for Renault) Open the seat frame cladding under the seat.
Fig. 15: (for Mercedes) Open the seat frame cladding under the seat.
Fig. 16:
Fold the seat frame cladding under the seat cover. Pull the strap through
between the seat and the backrest. Then close the fastener at the back.
Fig. 17+18: Reißverschlüsse an der oberen Seite des Lehnenbezugs so öffnen, dass
die Montageöffnungen der Kopfstütze freiliegen.
Bild 19:
Kopfstütze des Vordersitzes montieren und korrekten, straff sitzenden Be-
zug prüfen.
• Instructions for care and disposal
Wash the covers by hand
Do not use bleach
Do not dry in a tumbler
The seat covers can be disposed of in the household waste.
Please dispose of the packaging in accordance with the local regulations.
• Service & guarantee
This product has been produced with great care and under continuous quality control. The
product comes with a three year guarantee from date of purchase. Please keep your receipt
safe. The guarantee applies only to material and manufacturing defects and does not ap-
ply to misuse or improper treatment. Your statutory rights, especially the rights of warranty,
are not restricted by this guarantee.
Extent of validity: Please use the service hotline which has been provided for you or contact
the service centre in the European Economic Area.
Costs: Repair or replacement free of charge or a refund of the purchase cost. Shipping
costs will not be charged.
Advisory notice: Before returning your product, contact our hotline by telephone, so
that we can help you with any operating errors.
Service address:
Walser Industrie- und Handels GmbH
office@walsergroup.com
www.walsergroup.com
Service Hotline: 00800 00300030
IAN 337946_2001
Do not iron
Do not dry clean
Return address:
Walser Customer Service Germany
Walser GmbH
Bleicheweg 15, Postfach 3325
DE-88131 Lindau
GERMANY