Sygonix TX 1 Bedienungsanleitung Seite 3

Operating instructions
GB
Room Thermostat "tx.1", AP
Intended use
The product is intended to be used for regulating the temperature in living and offi ce
spaces.
Always observe the safety instructions and all other information included in these ope-
rating instructions!
Any other use than that described above may damage the product. Moreover, this
may give rise to hazards such as short-circuiting, fi re, electric shock, etc. No part of the
product may be modifi ed or converted!
This Product Meets Legal, National and European Requirements. All names of com-
panies and products are the trademarks of the respective owner. All rights reserved.
Package Contents
• Room Thermostat
• Operating Instructions
Explanation of the Symbols
The lightning symbol indicates a health hazard, e.g. electric shock.
This symbol indicates specifi c risks associated with handling, function and
use.
Safety Instructions
Read the complete operating manual carefully before using the product,
as it contains important information about the correct installation and
operation.
The warranty will be void in the event of damage caused by failure to ob-
serve these safety instructions! We do not assume any liability for any
consequential damage!
We do not assume any liability for material and personal damage caused
by improper use or non-compliance with the safety instructions! The
warranty will be void in such cases!
Caution!
This device should only be installed by people with relevant electro-tech-
nical knowledge and experience!
If it is installed improperly, you risk:
- Your own life;
- The life of the user of the electrical system.
If it is installed improperly, you risk severe damage to property, e.g. by fi re.
You face the risk of personal liability for people injury and material damage.
Contact an electrician!
• The unauthorised conversion and/or modifi cation of the product is not al-
lowed for safety and approval reasons (CE).
• The product is not a toy and must be kept out of the reach of children! There
is a risk of a lethal electric shock!
• The product may only be operated on the mains voltage (see section "Tech-
nical Data"). Never try to operate the product at another voltage as this will
cause its destruction.
• This product is only to be installed and used in dry conditions indoors. The
product must not get damp or wet as this may damage it; danger of a fatal
electric shock!
• Do not use this product in rooms or under adverse ambient conditions
where combustible gases, vapours or dust are or may be present! There is a
risk of explosion!
• The product must not be exposed to extreme temperatures, strong vibra-
tions or heavy mechanical stress.
The home technology brand for the entire house. More information at www.sygonix.com
• If you have reason to assume that safe operation is no longer possible, dis-
connect the product immediately and secure it against inadvertent opera-
tion. After this, let an expert check the product.
It can be assumed that safe operation is no longer possible if:
- the product shows visible signs of damage,
- the product does not work at all or works poorly (fl ickering light, leaking
smoke or a smell of burning, the light fl ickers, audible cracking noises, dis-
colouration to the product or the adjacent surfaces.)
- the product was stored under unfavourable conditions
- it was exposed to heavy loads during transport
• Do not leave packaging material carelessly lying around since it could be-
come a dangerous plaything for children.
• In commercial institutions, the accident prevention regulations of the em-
ployer's liability insurance association for electrical systems and operating
facilities are to be observed!
• If you have any questions that are not answered in this manual, please
contact our technical service or another specialist.
Preparations for Connection and Installation
• The device must be voltage-free during installation and connection.
Turn the power off and ensure that none of the poles is carrying a current by remo-
ving the electric circuit's fuse, or switching off at the circuit breaker. Secure it against
unauthorised reconnection, e.g., with a danger sign. In addition, switch off the ap-
propriate earth-leakage circuit breaker.
• Check that the mains cable is free of current e.g. with an appropriate tester.
• Choose a suitable place for installation. To ensure the thermostat functions without
fault, it must be installed so it is not close to heaters, windows, doors, etc. Also keep
the thermostat out of drafts.
Do not mount the thermostat behind furniture or curtains.
Because the exterior walls of a building are generally colder than the walls in the in-
terior of the building (depending on the building insulation), the thermostat should
not be mounted there.
Wall heaters work with air convection. Thus, warm air rises from the heater, cools
slowly and sinks back down on the other side of the room. Therefore, an ideal lo-
cation for installing the thermostat is on the wall opposite a heater; see fi gure. The
ideal installation height for this purpose is approx. 1.5 m.