Operation - Makita TD022D Betriebsanleitung

Installing or removing driver bit/
socket bit
► Fig.6
Use only driver bit/socket bit that has inserting portion
shown in the figure. Do not use any other driver bit/
socket bit.
For tool with shallow driver bit hole
A=12mm
B=9mm
For tool with deep driver bit hole
A=17mm
B=14mm
A=12mm
B=9mm
Procedure 1
► Fig.7: 1. Driver bit 2. Sleeve
To install the driver bit, pull the sleeve in the direction of
the arrow and insert the driver bit into the sleeve as far
as it will go.
Then release the sleeve to secure the driver bit.
Procedure 2
In addition to Procedure 1, insert the bit-piece into the
sleeve with its pointed end facing in.
► Fig.8: 1. Driver bit 2. Bit-piece 3. Sleeve
To remove the driver bit, pull the sleeve in the direction
of the arrow and pull the driver bit out.
NOTE: If the driver bit is not inserted deep enough
into the sleeve, the sleeve will not return to its original
position and the driver bit will not be secured. In this
case, try re-inserting the bit according to the instruc-
tions above.
NOTE: After inserting the driver bit, make sure that it
is firmly secured. If it comes out, do not use it.

OPERATION

CAUTION:
When bending the tool to use in
the pistol shape or straightening to use in the
straight shape, do not hold the bendable part of
the tool. Failure to do so may cause your hand and
fingers to be pinched and injured by this part.
► Fig.9: 1. Straight shape 2. Pistol shape
The tool can be used in two ways; a straight shape and
a pistol shape which are selectable according to the
conditions of workplace and screwdriving.
The proper fastening torque may differ depending upon
the kind or size of the screw/bolt, the material of the
workpiece to be fastened, etc. The relation between fas-
tening torque and fastening time is shown in the figures.
Use only these type of driver
bit. Follow the procedure
1. (Note) Bit-piece is not
necessary.
To install these types of driver
bits, follow the procedure 1.
To install these types of driver
bits, follow the procedure 2.
(Note) Bit-piece is necessary
for installing the bit.
Standard bolt
N•m
(kgf•cm)
20
(204)
15
(153)
2
10
(102)
5
(51)
0
1. Fastening time (second) 2. Fastening torque
3. Proper fastening torque corresponding to each bolt
diameter
High tensile bolt
N•m
(kgf•cm)
20
(204)
15
(153)
2
10
(102)
5
(51)
0
1. Fastening time (second) 2. Fastening torque
3. Proper fastening torque corresponding to each bolt
diameter
Hold the tool firmly and place the point of the driver bit
in the screw head. Apply forward pressure to the tool to
the extent that the bit will not slip off the screw and turn
the tool on to start operation.
NOTICE:
If you use a spare battery to continue
the operation, rest the tool at least 15 min.
NOTE: Use the proper bit for the head of the screw/
bolt that you wish to use.
NOTE: When fastening M5 or smaller screw, carefully adjust
rotation angle on the switch so that the screw is not damaged.
NOTE: Hold the tool pointed straight at the screw.
NOTE: If the impact force is too strong or you tighten the
screw for a time longer than shown in the figures, the screw or
the point of the driver bit may be overstressed, stripped, dam-
aged, etc. Before starting your job, always perform a test oper-
ation to determine the proper fastening time for your screw.
7 ENGLISH
M8
M8
M6
M6
1 2 3
1
M6
M6
1 2 3
1
3
3