cecotec Ready Warm 800 Thermal Bedienungsanleitung Seite 11

ENGLISH
room one. The room temperature is shown on the display.
as the temperature shown on the display is the one next to the device and not the real room
one, when setting the temperature, select a few more grades than desired ones.
• Turning the device on:
• Connect the device to a power supply and turn the power switch on (2). The control
panel will flash and the "ºC" symbol, room temperature and power indicator
light up. If this last symbol does not light up, press it.
• Select the desired operating mode by pressing the corresponding button: day
night or anti-frost . The display will show the selected mode.
• Use the + and – buttons to set the desired temperature for the selected mode. While
the temperature is being set, the "ºC" icon will blink.
• Once the desired temperature has been set, the display will show the room
temperature again.
• Repeat the before steps to set the temperature for the other modes.
• Use the on/off button to turn the radiator on and off.
• Thermostat:
• When the device reaches the set temperature, it will automatically switch off and
the icon will turn off.
• When the room temperature falls below the set one, the device will automatically
turn back on and the icon will light up again.
Note:
The may blink when the device is about to turn on or off.
the set temperatures will be saved even if the device is disconnected or turned off and on.
• Reset:
• To reset the device while it is connected to the power supply and the power switch is
on, make sure the device is unlocked or unlock it with the remote control and press
the power button (-) for 3 seconds or switch it off from the power switch (2).
2. PROGRAMMED
• 3 operating modes:
• Day mode : the temperature can be set from 5 to 35 ºC.
• Night mode : the temperature can be set from 5 to 35 ºC.
• Anti-frost mode : the temperature can be set from 5 to 15 ºC.
• The temperature set manually will be applied to the modes during programmed
operations.
• Setting current time and day:
• Long press the "PROG" button until the display shows "00:00".
• The hour digits will blink. Use the + and – buttons to set the desired hour and press
20 READY WARM THERMAL
"PROG" to save the settings.
• The minutes digits will blink. Use the + and – buttons to set the desired minutes and
press "PROG" to save the settings.
• The display will show the week calendar (Monday-Sunday, 1-7). Select the current
day by pressing + and -. Press "PROG" to save the settings.
• Setting weekly schedule:
will
• The display will show the first 2 bars for the first period of time (00:00 – 1:00 am)
blinking. It will also show 1 as Monday.
,
• Press the desired mode (day, night or anti-frost) for the selected time interval.
• Once the first period has been scheduled, press "+" and the next time period's bars
will blink.
• Repeat these steps up to 24 hours.
• When all the hours in a day have been scheduled, press "PROG" to end the selected
day scheduling and repeat the steps to schedule the 7 days of the week.
• Once the whole week has been scheduled, press "PROG" and the device will
automatically save the settings and operate in the set mode.
WARNING: if the device is disconnected from the power supply, the schedule settings will be
saved but the current day and time will be reset.
• Resetting the current time and day:
• To unblock the appliance, long-press "PROG" until the display shows "00:00". The
hour digits will flash, use the + and – buttons to select the desired hour, press "PROG"
to switch to minutes settings and use the + and – buttons again. Press "PROG" to
save the settings.
• The display will show the week calendar (1-7). Set the current day using the + and –
buttons and press the power switch twice. Then, press "PROG" and the + or – button.
• Adjusting temperature under programmed mod:
• During operation, press twice the on button on the remote control and use the + and
– button to select the desired temperature.
• Once the temperature is set, it will be saved for this mode for future operations,
including under manual mode.
Note: if the appliance is operating under programmed mode, to change it:
• Press the on button on the remote control twice.
- If you select night mode, the display will show
will blink.
- If you select the anti-frost mode, the display will show
lower part will blink.
- If you select day mode, the display will show
will blink.
ENGLISH
and the bar on the top part
and the bar on the
and the top and lower bars
READY WARM THERMAL 21