Optional Accessory - Makita DLS110 Betriebsanleitung

Example:
In the case of cutting 52/38° type crown molding for
position (a) in the above figure:
• Tilt and secure bevel angle setting to 33.9° RIGHT.
• Adjust and secure miter angle setting to 31.6°
RIGHT.
• Lay crown molding with its broad back (hidden)
surface down on the turn base with its WALL
CONTACT EDGE against the guide fence on the
saw.
• The finished piece to be used will always be on
the RIGHT side of the blade after the cut has been
made.
Crown molding stopper

Optional accessory

Crown molding stoppers allow easier cuts of crown
molding without tilting the saw blade. Install them on the
turn base as shown in the figures.
At right 45° miter angle
► Fig.53: 1. Crown molding stopper L 2. Crown mold-
ing stopper R 3. Turn base 4. Guide fence
At left 45° miter angle
► Fig.54: 1. Crown molding stopper L 2. Crown mold-
ing stopper R 3. Turn base 4. Guide fence
Position crown molding with its WALL CONTACT EDGE
against the guide fence and its CEILING CONTACT
EDGE against the crown molding stoppers as shown in
the figure. Adjust the crown molding stoppers according
to the size of the crown molding. Tighten the screws to
secure the crown molding stoppers. Refer to the table
(C) for the miter angle.
► Fig.55: 1. Guide fence 2. Crown molding stopper
(a) (b)
1. Inside corner 2. Outside corner
Table (C)
– Molding
position in
the figure
For inside (a)
corner
(b)
For outside (c)
corner
(d)
(c) (d)
1 2
Miter angle Finished
piece
Right 45° Save the right
side of blade
Left 45° Save the left
side of blade
Save the right
side of blade
Right 45° Save the left
side of blade
Cutting aluminum extrusion
► Fig.56: 1. Vise 2. Spacer block 3. Guide fence
4. Aluminum extrusion 5. Spacer block
When securing aluminum extrusions, use spacer blocks
or pieces of scrap as shown in the figure to prevent
deformation of the aluminum. Use a cutting lubricant
when cutting the aluminum extrusion to prevent build-up
of the aluminum material on the blade.
WARNING:
round aluminum extrusions. Thick or round alumi-
num extrusions can be difficult to secure and the work
may loosen during the cutting operation which may
result in loss of control and serious personal injury.
Groove cutting
WARNING:
type of cut by using a wider type blade or dado
blade. Attempting to make a groove cut with a wider
blade or dado blade could lead to unexpected cutting
results and kickback which may result in serious
personal injury.
WARNING:
to the original position when performing other
than groove cutting. Attempting to make cuts with
the stopper arm in the incorrect position could lead to
unexpected cutting results and kickback which may
result in serious personal injury.
For a dado type cut, perform as follows:
1.
Adjust the lower limit position of the saw blade
using the adjusting screw and the stopper arm to limit
the cutting depth of the saw blade. Refer to the section
for stopper arm.
2. After adjusting the lower limit position of the saw
blade, cut parallel grooves across the width of the work-
piece using a slide (push) cut.
► Fig.57: 1. Cut grooves with blade
3. Remove the workpiece material between the
grooves with a chisel.
Carrying tool
Before carrying, make sure to remove the batteries and
all movable parts of the miter saw are secured. Always
check the following:
• The batteries are removed.
• The carriage is at 0° bevel angle position and
secured.
• The carriage is lowered and locked.
• The carriage is fully slid to the guide fence and
locked.
• The turn base is at the full right miter angle posi-
tion and secured.
• The holders are stored and secured.
Carry the tool by holding both sides of the tool base as
shown in the figure.
► Fig.58
31 ENGLISH
Never attempt to cut thick or
Do not attempt to perform this
Be sure to return the stopper arm