Functional Description - Makita DF001D Betriebsanleitung

Cordless screwdriver safety warnings
1. Hold the power tool by insulated gripping
surfaces, when performing an operation
where the fastener may contact hidden wiring.
Fasteners contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
Always be sure you have a firm footing.
2.
Be sure no one is below when using the tool in
high locations.
Hold the tool firmly.
3.
4. Keep hands away from rotating parts.
5. Do not touch the bit or the workpiece immedi-
ately after operation; they may be extremely
hot and could burn your skin.
6. Always secure workpiece in a vise or similar
hold-down device.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product.
MISUSE or failure to follow the safety rules stated
in this instruction manual may cause serious
personal injury.
Important safety instructions for
built-in battery
Before using built-in battery, read all instructions
1.
and cautionary markings on (1) battery charger,
(2) battery, and (3) product using battery.
2. Do not disassemble built-in battery.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them
out with clear water and seek medical atten-
tion right away. It may result in loss of your
eyesight.
5. Do not short the built-in battery:
(1) Do not touch the terminals with any con-
ductive material.
(2) Avoid storing built-in battery in a con-
tainer with other metal objects such as
nails, coins, etc.
(3) Do not expose built-in battery to water or
rain.
A battery short can cause a large current
flow, overheating, possible burns and even a
breakdown.
6. Do not store the tool and built-in battery in
locations where the temperature may reach or
exceed 50 °C (122 °F).
7. Do not incinerate the built-in battery even if
it is severely damaged or is completely worn
out. The built-in battery can explode in a fire.
8. Be careful not to drop or strike battery.
Do not use a damaged battery.
9.
10. The contained lithium-ion batteries are subject to
the Dangerous Goods Legislation requirements.
For commercial transports e.g. by third parties,
forwarding agents, special requirement on pack-
aging and labeling must be observed.
For preparation of the item being shipped, consulting an
expert for hazardous material is required. Please also
observe possibly more detailed national regulations.
Tape or mask off open contacts and pack up the battery in
such a manner that it cannot move around in the packaging.
11. Follow your local regulations relating to dis-
posal of battery.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum
battery life
Charge the built-in battery before completely dis-
1.
charged. Always stop tool operation and charge the
built-in battery when you notice less tool power.
Never recharge a fully charged built-in battery.
2.
Overcharging shortens the battery service life.
3. Charge the built-in battery with room tempera-
ture at 10 °C - 40 °C (50 °F - 104 °F). Let a hot
built-in battery cool down before charging it.
4. Charge the built-in battery if you do not use it
for a long period (more than six months).
FUNCTIONAL
DESCRIPTION
CAUTION:
Always be sure that the tool is
switched off before adjusting or checking func-
tion on the tool.
Charging the built-in battery
CAUTION:
Use only the Makita AC adapter
and USB cable to charge the tool. Use of the other
type AC adapter and USB cable may cause the bat-
tery to burst, result in personal injury and damage.
CAUTION:
Always disconnect the charging
plug from the tool after charging.
► Fig.1
► Fig.2
Connect the USB cable to the AC adapter, and then plug the
AC adapter into the mains supply. Open the connector cover
on the tool, and then connect the USB cable to the connector.
Before the first use, be sure to charge the built-in bat-
tery. It takes approximately 3 to 5 hours to fully charge
the battery. The charging time varies depending on the
usage conditions and remaining battery capacity.
Unplug the USB cable from the tool, and then close the
connector cover.
NOTE: While charging, the built-in battery and AC
adapter may become warm. This is normal and will
continue until the built-in battery is fully charged and
the AC adapter has been disconnected from the
mains supply.
5 ENGLISH