Suggestions For Maintaining A Nice Lawn; Emptying The Grass Catcher; After Operation; Routine Maintenance - Stiga Cruiser 430 Li 60-Serie Gebrauchsanweisung

3. The appearance of the lawn will improve
if you alternate cutting in both directions
at the same height (Fig.17.0).
For side discharge: it is best to mow in a pattern where
cut grass is not discharged on the grass still to be cut.
For mulching or rear grass discharge:
• Always avoid removing a large quantity of
grass. Never cut more than one third of the
total grass height per single pass (Fig.18).
• Keep the chassis perfectly clean (par. 7.3.1).
6.4.2

Suggestions for maintaining a nice lawn

• To keep a lawn green and soft with a good appearance,
it should be cut regularly. A lawn can be composed of
different types of grass. If the lawn is cut frequently,
grass and roots grow more vigorously, forming a solid
grassy bed. If the lawn is cut is less frequently, higher
grass and weeds start growing (clover and daisies,
etc.). The frequency of mowing should be in relation
to the rate of growth of the grass, which should not be
left to grow too much between one cut and the next.
• The best height of the grass on a well-kept lawn
is approx. 4-5 cm. and with one mowing, you do
not need to remove more than a third of the total
height. If the grass is very tall, it should be cut
twice in a twenty-four hour period; the first time
with the cutting means at maximum cutting height,
and the second cut at the height desired.
• Cutting too low tears and uproots the grass,
giving it a "spotted" appearance.
• During hot and dry periods, the grass should be cut a
little higher to prevent the ground from drying out.
• It is always better to cut the grass when dry. Do
not cut wet grass; this could reduce cutting means
efficiency due to sticky grass and tear the lawn.
• The cutting means must be in good condition and well
sharpened so that the grass is cut straight without a
ragged edge that leads to yellowing at the ends.
6.4.3

Emptying the grass catcher

When the grass catcher (Fig.1.G) is too full,
grass collection is no longer efficient and
the sound of the lawnmower changes.
For a grass catcher with contents indicator device:
1. Up = empty.
2. Down = full.
While working with the cutting means running, the
indicator remains raised for as long as the grass catcher
is able to hold cut grass; when it lowers, it means
that the grass catcher is full and must be emptied.
To remove and empty the grass catcher:
1. Release the control lever (Fig.19.A).
2. Wait until the cutting means stop.
3. Lift the rear discharge guard (Fig.11.A),
grasp the handle and remove the grass
catcher keeping it in an erect position.
6.5 STOP
To stop the machine:
1. Release the control lever (Fig.19.A).
2. Wait until the cutting means stop.
When you have stopped the machine, it will take a
few seconds for the cutting means to stop.
IMPORTANT Always stop the machine.
• When moving between work areas.
• When driving on grass free surfaces.
• Every time it is necessary to overcome an obstacle.
• Before adjusting the cutting height.
• Whenever you remove or reattach the grass catcher.
• Whenever you remove or reattach the
side discharge chute (if provided).
6.6

AFTER OPERATION

1. Stop the machine (par. 6.5).
2. Open the battery housing hatch and remove the
safety key (Fig. 20.A).
Press the flap in the battery housing (Fig.20.B)
3.
and remove the battery (Fig.20.C).
4. Recharge it (par 7.2.2).
5. Allow the motor to cool before sto-
ring in an enclosed space.
6. Clean (par. 7.3).
7. Check there are no loose or damaged compo-
nents. If necessary, replace the damaged com-
ponents and tighten any screws and loose bolts
or contact the authorised service centre.
IMPORTANT Remove the safe key whenever
the machine is unused or left unattended.
7.

ROUTINE MAINTENANCE

7.1

GENERAL INFORMATION

The safety regulations to follow are described in
chap. 2. Strictly comply with these indications to avoid
serious risks or dangers.
Before conducting any inspections, cleaning or
maintenance/adjustment interventions on the machine:
• Stop the machine.
• Remove the safety key, (never leave the
key in the ignition or within reach of
children or unauthorised persons).
• Remove the battery.
• Make sure that all moving parts have
come to a complete stop.
• Allow the motor to cool before
storing in an enclosed space.
• Read the relevant instructions.
EN - 8