Ec Declaration Of Conformity; Maintenance - Milwaukee M18 FMCS66 Originalbetriebsanleitung

1. Release the trigger and remove battery pack.
2. Remove t he blade from the workpiece.
3. Allow the tool to rest for a minimum of two minutes.
4. Allow the tool to run under no load to ensure the tool has
properly cooled.
5. Resume the cut. When restarting a saw in the
workpiece, center the saw blade in the kerf, or cut, and
check that saw teeth are not engaged into the material.
If saw blade is binding, it may walk up or KICKBACK
from the workpiece as the saw is restarted.
ELECTRIC BRAKE
The electric brake engages when the trigger is released,
causing the blade to stop and allowing you to proceed with
your work. Generally, the saw blade stops within two
seconds. However, there may be a delay between the time
you release the trigger and when the brake engages.
Occasionally the brake may miss completely. If the brake
misses frequently, the saw needs servicing by an
authorized Milwaukee service facility.
You must always wait for the blade to stop completely
before removing the saw from the workpiece.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
described under "Technical Data" fulfi lls all the relevant
regulations and the directives 2011/65/EU (RoHS),
2014/30/EU, 2006/42/EC, and the following harmonized
standards have been used:
EN 62841-1:2015
EN 62841-2-5:2014
EN 55014-1:2017
EN 55014-2:2015
EN IEC 63000:2018
Winnenden, 2020-03-05
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
BATTERIES
Battery packs which have not been used for some time
should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the
performance of the battery pack. Avoid extended exposure
to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept
clean.
For an optimum life-time, the battery packs have to be fully
charged, after used.
To obtain the longest possible battery life remove the
battery pack from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below
27°C and away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
BATTERY PACK PROTECTION
In extremely high torque, binding, stalling and short circuit
situations that cause high current draw, the tool will vibrate
for about 2 seconds and then the tool will turn OFF.
To reset, release the trigger.
30 ENGLISH
Under extreme circumstances, the internal temperatur of
the battery could become to high. If this happens, the
battery will shut down.
Place the battery on the charger to charge and reset it.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
Transportation of those batteries has to be done in
accordance with local, national and international provisions
and regulations.
• The user can transport the batteries by road without
further requirements.
• Commercial transport of Lithium-Ion batteries by third
parties is subject to Dangerous Goods regulations.
Transport preparation and transport are exclusively to be
carried out by appropriately trained persons and the
process has to be accompanied by corresponding
experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and
insulated to prevent short circuit.
• Ensure that battery pack is secured against movement
within packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice

MAINTENANCE

The ventilation slots of the machine must be kept clear at
all times.
Be sure to disconnect the tool from the power supply
before attaching or removing the saw blade.
Clean tool and guarding system with dry cloth. Certain
cleaning agents and solvents are harmful to plastics and
other insulated parts. Keep the apparatus handle clean, dry
and free of spilt oil or grease. Check the function of guards.
Regular maintenance and cleaning provide for a long
service life and safe handling.
Remove dust regularly. Remove the sawdust which has
accummulated inside the saw in order to avoid the risk of
fi re.
Use only Milwaukee accessories and Milwaukee spare
parts. Should components need to be replaced which have
not been described, please contact one of our Milwaukee
service agents (see our list of guarantee/service
addresses).
If needed, an exploded view of the tool can be ordered.
Please state the machine type printed as well as the
six-digit No. on the label and order the drawing at your
local service agents or directly at: Techtronic Industries
GmbH, Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any
work on the machine.
Please read the instructions carefully before
starting the machine.
Wear gloves!
Wear ear protectors!
Always wear goggles when using the machine.
Wear a suitable dust protection mask.
Accessory - Not included in standard equipment,
available as an accessory.
Do not dispose electric tools, batteries/
rechargeable batteries together with household
waste material.
Electric tools and batteries that have reached
the end of their life must be collected separately
and returned to an environmentally compatible
recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
n No-load speed
0
V Volts
Direct current
Rotation direction
European Conformity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark
ENGLISH 31