MyTek Hoogo R2 Bedienungsanleitung Seite 11

20
NOTE:
Recharge the appliance when the battery
indicator (Fig. 1 / 3) on the appliance lights
up with constant red light.
> Setting the anti-fall sensors
Your robot vacuum cleaner automatically de-
tects dropoffs in front of it by means of 3 anti-
fall sensors (Fig. 2). As a result, it changes its
direction of travel and continues to clean in the
opposite direction. Lower-level surfaces, such
as stairs are detected and thus omitted from
the cleaning. You can adjust the sensitivity of
the anti-fall sensors as follows:
WARNING!
Test the correct settings repeatedly while
you are present to avoid damage by incor-
rect settings.
Ensure that the ON / OFF switch is in position 0
1
(Fig. 11 / B).
Adjust the position of the slide controllers to
2
set the sensitivity of the anti-fall sensors at
the bottom of the appliance (Fig. 1 / 12):
· Position 0 (smallest opening) for
light floors and low steps
· Position 1 (Fig. 12 / B) for light floors
and slightly higher steps
· Position 2 for dark floors and even
higher steps
· Position 3 (largest opening, Fig. 12 / A)
for dark floors and high steps.
NOTE:
All 3 slide controllers have to be set to the
same setting. If your robot constantly travels
backward on dark floors, you must select
position 3 (largest opening).
> Cleaning floors
NOTE:
To clean short pile carpets, remove the
round brooms first. To do so, grab the bristles
and firmly pull the round brooms upwards
(Fig. 13 / B). Do not use the appliance on long
pile carpets.
EN
To switch on the appliance, place it on the floor
and set the ON / OFF switch to position I (Fig. 11 / A).
Both external LEDs flash alternately.
After approx. 8 seconds the appliance will start
to move in "random mode" (Fig. 3 / A).
After approx. 1.5 minutes the appliance changes
to "gyro mode", moving in ever increasing
circles (Fig. 3 / B). As soon as the appliance en-
counters an obstacle in this mode, it changes to
"edge mode" (Fig. 4 / A), traversing the edges of
the room to be cleaned for approx. 2.5 minutes.
Then the cycle starts all over again with
"random mode" (Fig. 4 / B).
NOTE:
If the appliance has become stuck on an ob-
stacle, give it a gentle push with your hand.
NOTE:
When the performance of the battery pack
diminishes, the battery indicator (Fig. 1 / 3)
remains red and the appliance stops soon
afterwards. If this is the case, the appliance
will beep every 60 seconds to make it easier
to locate it. (If the battery pack is completely
flat, the beep function will stop.) Then switch
off the appliance and charge the battery
pack > "Charging the battery pack" on page 19.
NOTE:
If you lift the appliance while it is in oper-
ation, the motors switch off automatically after
approximately 1 second without floor con-
tact. However, the appliance is not switched
off (the blue LED is still lit) and starts up again
as soon as it makes contact with a surface.
To switch off the appliance, set ON / OFF switch
to position 0 (Fig. 11 / B).
→ The LEDs go out.
> Emptying the dust bin
Ensure that the ON / OFF switch is in position 0
1
(Fig. 11 / B).
Reach into the recessed grip (Fig. 7 / 5) and
2
unlock the cover of the dust bin (Fig. 7 / 1).
Remove the dust bin comportment cover
3
(Fig. 7 / 1) from the appliance (Fig. 14).
Remove (Fig. 15) the dust bin cover (Fig. 7 / 2).
4
Carefully pull dust bin with the attached filter
5
from the appliance (Fig. 16).
Place dust bin with attached filter above a
6
waste bin and then separate dust bin from
filter. Tap both parts lightly and remove coar-
ser debris with a dry cloth.
> Cleaning the dust bin and the filter
Remove and empty the dust bin > "Emptying
1
the dust bin" on page 21.
Thoroughly rinse dust bin by hand under
2
running cold water or lukewarm water.
Thoroughly rinse filter by hand under
3
running cold water or lukewarm water.
Allow both elements to dry at room
4
temperature for at least 24 hours.
Reinsert filter into dust bin in such a way that
5
the plastic grid of the filter is visible. Firmly
push filter into place (Fig. 17).
Reinsert dust bin with filter into the appliance
6
> "Inserting dust bin and filter" on page 21.
> Inserting dust bin and filter
Reinsert dust bin with attached filter
1
into dust bin compartment (Fig. 17).
Put dust bin cover firmly in place
2
until you feel it engage (Fig. 18).
First, put the dust bin compartment cover in
3
place at the front so that the 3 tabs on the
cover engage in the 3 slots provided in the
dust bin compartment. Now press against the
dust bin compartment cover in the rear until
you hear and feel it click in place (Fig. 19).
EN
NOTE:
The appliance can only be switched on
again if the cover is positioned correctly.
> Removing the battery pack
Operate the appliance until the battery
1
pack is completely empty and the motor
of the appliance stops.
Place the ON / OFF switch to position 0
2
(Fig. 11 / B).
Firmly remove cover from battery
3
compartment (Fig. 5 / OPEN).
4 Remove the battery pack.
> Troubleshooting
Before you contact our customer service de-
partment or send the appliance to the hoogo
customer service department, you will find a lot
of additional information in the service area of
our website which will help you solve problems.
www.hoogo.world/service
WARNING!
Switch off the appliance before you start
troubleshooting. Never use a faulty
appliance, charger or rechargeable battery.
21