More Information; Installation / Connection; Basic Procedure - Kenwood DPX206U Bedienungsanleitung

MORE INFORMATION

General
• This unit can only play the following CDs:
• Detailed information and notes about the playable audio
files are stated in an online manual on the following
web site: www.kenwood.com/cs/ce/audiofile/
Playable files
• Playable audio file: MP3 (.mp3), WMA (.wma)
• Playable disc media: CD-R/CD-RW/CD-ROM
• Playable disc file format: ISO 9660 Level 1/2, Joliet, Long
file name.
• Playable USB device file system: FAT12, FAT16, FAT32
Even when audio files comply with the standards listed
above, playback may be impossible depending on the
types or conditions of media or device.
Unplayable discs
• Discs that are not round.
• Discs with coloring on the recording surface or discs that
are dirty.
• Recordable/ReWritable discs that have not been
finalized.
• 8 cm CD. Attempting to insert using an adapter may
cause malfunction.
About USB devices
• This unit can play MP3/WMA/WAV files stored on a USB
mass storage class device.
• You cannot connect a USB device via a USB hub.
• Connecting a cable whose total length is longer than
5 m may result in abnormal playback.
• This unit cannot recognize a USB device whose rating is
other than 5 V and exceeds 1 A.
12
About KENWOOD Music Editor Light and
KENWOOD Music Control
• This unit supports the PC application KENWOOD
Music Editor Light and Android™ application
KENWOOD Music Control.
• When you play audio files with song data
added using the KENWOOD Music Editor Light
or KENWOOD Music Control, you can search for
audio files by Genres, Artists, Albums, Playlists,
and Songs.
• KENWOOD Music Editor Light and KENWOOD
Music Control are available on the following
web site: www.kenwood.com/cs/ce/
About iPod/iPhone
Made for
- iPod touch (2nd, 3rd, 4th, and 5th generation)
- iPod classic
- iPod nano (3rd, 4th, 5th, 6th, and 7th
generation)
- iPhone 3G, 3GS, 4, 4S, 5, 5S, 5C
• For the latest compatible list and
software versions of iPhone/iPod, see:
www.kenwood.com/cs/ce/ipod
• You cannot operate iPod if "KENWOOD" or " " is
displayed on iPod.
About Android device
• This unit supports Android OS 4.1 and above.
• Some Android devices (with OS 4.1 and above)
may not fully support Android Open Accessory
(AOA) 2.0.
• If the Android device supports both mass storage
class device and AOA 2.0, this unit always
playback via AOA 2.0 as priority.
• For more information and the latest compatible
list, see: www.kenwood.com/cs/ce/

INSTALLATION / CONNECTION

Warning
• The unit can only be used with a 12 V DC power supply, negative ground.
• Disconnect the battery's negative terminal before wiring and mounting.
• Do not connect Battery wire (yellow) and Ignition wire (red) to the car
chassis or Ground wire (black) to prevent a short circuit.
• Insulate unconnected wires with vinyl tape to prevent a short circuit.
• Be sure to ground this unit to the car's chassis again after installation.
Caution
• For safety's sake, leave wiring and mounting to professionals. Consult the
car audio dealer.
• Install this unit in the console of your vehicle. Do not touch the metal
parts of this unit during and shortly after use of the unit. Metal parts such
as the heat sink and enclosure become hot.
• Do not connect the [ wires of speakers to the car chassis or Ground wire
(black), or connect them in parallel.
• Mount the unit at an angle of less than 30º.
• If your vehicle wiring harness does not have the ignition terminal,
connect Ignition wire (red) to the terminal on the vehicle's fuse box
which provides 12 V DC power supply and is turned on and off by the
ignition key.
• Keep all cables away from heat dissipate metal parts.
• After the unit is installed, check whether the brake lamps, blinkers,
wipers, etc. on the car are working properly.
• If the fuse blows, first make sure the wires are not touching car's chassis,
then replace the old fuse with one that has the same rating.

Basic procedure

1 Remove the key from the ignition switch, then
disconnect the [ terminal of the car battery.
2 Connect the wires properly.
See Wiring connection. ( 14)
3 Install the unit to your car.
See Installing the unit (in-dash mounting).
Connect the [ terminal of the car battery.
4
5
Reset the unit. ( 3)