Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
4. Cleaning and testing
4. Cleaning and testing
After completion of work, the equipment should
After completion of work, the equipment should
be cleaned of any contamination. This increases
be cleaned of any contamination. This increases
the service life duration of this type of PPE, as
the service life duration of this type of PPE, as
well as your security. Clean with warm water at
well as your security. Clean with warm water at
30°C and fabric-sensitive detergent and then dry
30°C and fabric-sensitive detergent and then dry
in the shade. Clean belts have a longer service
in the shade. Clean belts have a longer service
life. Rub metal fittings regularly with an oily cloth
life. Rub metal fittings regularly with an oily cloth
(e.g. WD 40).
(e.g. WD 40).
5. Storage
5. Storage
Storage should be implemented in dry
Storage should be implemented in dry
conditions in a sealed metal suitcase or PVC
conditions in a sealed metal suitcase or PVC
bag (aerated and protected against direct solar
bag (aerated and protected against direct solar
radiation).
radiation).
6. Verification
6. Verification
If there is doubt as to whether the equipment is
If there is doubt as to whether the equipment is
safe to use, it must be recalled immediately
safe to use, it must be recalled immediately
before being used. If it has been strained,
before being used. If it has been strained,
personal protective equipment may only be
personal protective equipment may only be
reused with the written consent of a technical
reused with the written consent of a technical
expert. Regular verification may be implemented
expert. Regular verification may be implemented
through an expert person only, subject to
through an expert person only, subject to
precise observation of the directions of the
precise observation of the directions of the
manufacturer. Personal protective (retaining)
manufacturer. Personal protective (retaining)
equipment must be checked as necessary by a
equipment must be checked as necessary by a
technical expert, however at least once every
technical expert, however at least once every
twelve months. The manufacturer is considered
twelve months. The manufacturer is considered
an expert. The identification on the product must
an expert. The identification on the product must
also be checked for legibility.
also be checked for legibility.
Single components employed:
Single components employed:
Webbing:
Polyester (PES)
Webbing:
Polyester (PES)
Sewing thread:
Polyester (PES)
Sewing thread:
Polyester (PES)
Metal fittings:
steel optional zinc coated
Metal fittings:
steel optional zinc coated
aluminium or stainless steel
Plastic parts:
aluminium or stainless steel
Polyamide (PA)
Plastic parts:
Polyamide (PA)
7. Explanation of the pictograms
7. Explanation of the pictograms
It is absolutely necessary to read the
It is absolutely necessary to read the
direction for use before use of this
direction for use before use of this
PPE and to consider the warnings.
PPE and to consider the warnings.
8. Remarks
8. Remarks
Good maintenance and storage extend the
Good maintenance and storage extend the
longevity of your personal protective equipment
longevity of your personal protective equipment
and as such, ensure optimum safety.
and as such, ensure optimum safety.
The maximum service life of PPE depends on its
The maximum service life of PPE depends on its
condition and for products of MAS GmbH is up
condition and for products of MAS GmbH is up
.
to 8 years
.
to 8 years
In case of a complete documentation of the
In case of a complete documentation of the
annual expert inspections and a positive
annual expert inspections and a positive
assessment by an expert, the lifetime can be
assessment by an expert, the lifetime can be
extended to 10 years.
extended to 10 years.
A test log is enclosed with these directions for
A test log is enclosed with these directions for
use (control chart). Prior to the first application,
use (control chart). Prior to the first application,
this inspection log is to be filled in by the user
this inspection log is to be filled in by the user
with the necessary information. In case of resale
with the necessary information. In case of resale
in another country, the vendor must make
in another country, the vendor must make
available for the safety for the vendor the
available for the safety for the vendor the
directions for use, maintenance, , pt416> ,
directions for use, maintenance, , pt416> ,
which are normally used for chacks and service
which are normally used for chacks and service
in the language of the country
in the language of the country
Testing institute and production control:
Testing institute and production control:
Technical Committee "Personal Protective
Technical Committee "Personal Protective
Equipment"
Equipment"
Zentrum für Sicherheitstechnik,
Zentrum für Sicherheitstechnik,
Zwengenberger Straße 68,
Zwengenberger Straße 68,
42781 Haan, ID nummer: 0299
42781 Haan, ID nummer: 0299
In the course of the extended product liability we
In the course of the extended product liability we
point out that no liability is assumed on the part
point out that no liability is assumed on the part
of the manufacturer in case of any inappropriate
of the manufacturer in case of any inappropriate
use of the device.
use of the device.
Consider also the accident-prevention
Consider also the accident-prevention
specifications valid in each case!
specifications valid in each case!
Size table for safety belts
Size table for safety belts
Model B4
Model B4
Size
Size
Belt length
Belt length
in mm
in mm
Circumference of
750
Circumference of
abdomen/ body
750
abdomen/ body
1
2
1
2
1550
1750
1550
1750
–
–
1200
1100
1500
–
–
1200
1100
1500
13
Werbung
Inhaltsverzeichnis
