Protecting The Environment - Black+Decker KS800S-Serie Bersetzung Der Ursprünglichen Bedienungsanleitung

ENGLISH
The laser visibility (power) will be reduced if the jigsaw is
overheated. The laser may not be visible when the saw is
overloaded for a prolonged period of time. The laser visibility
will gradually return to normal when the tool cools down even
when the tool is unplugged.
Warning! Do not leave the overheated laser switched ON.
Make sure that the switch is in the OFF position and remove the
batteries to remove power from the laser.
Using the laser (fig. J and K)
The laser projects the line of cut (18) on to the surface of the
workpiece.
To switch the laser on, press the button (16).
To switch the laser off, press the button (16) again.
Viewing from directly above the jigsaw, the line of cut (17)
can be easily followed. Should this view be restricted for any
reason, the laser can be used as an alternative cutting guide.
Use a pencil to mark the cutting line (17).
Position the jigsaw over the line (17).
Switch on the laser.
Operating the work light (fig. L and M) ('W' units only)
Units that include a 'W' in the catalogue number are provided
with an LED light (19) to illuminate the area around the
blade.
To switch the work light on, slide the switch (20) to the on
position (I).
To switch the work light off, slide the switch (20) to the
off position (0).
Hints for optimum use
Sawing laminates
When cutting laminates, splintering may occur which can
damage the presentation surface. The most common saw
blades cut on the upward stroke, therefore if the shoe plate
is sitting on the presentation surface either use a saw blade
that cuts on the downward stroke or:
Use a fine-tooth saw blade.
Saw from the back surface of the workpiece.
To minimise splintering, clamp a piece of scrap wood or
hardboard to both sides of the workpiece and saw
through this sandwich.
Sawing metal
Be aware that sawing metal takes much more time than
sawing wood.
Use a saw blade suitable for sawing metal.
When cutting thin sheet metal, clamp a piece of scrap
wood to the back surface of the workpiece and cut
through this sandwich.
Spread a film of oil along the intended line of cut.
10
Maintenance
Your Black & Decker tool has been designed to operate over
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Never let any liquid get inside the tool and never
immerse any part of the tool into liquid.

Protecting the environment

Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker
product needs replacement, or if it is of no further
use to you, do not dispose of it with household
waste. Make this product available for separate
collection.
Separate collection of used products and packaging
allows materials to be recycled and used again. Re-
use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have
reached the end of their working life. To take advantage of
this service please return your product to any authorised
repair agent who will collect them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of
our after-sales service and contacts are available on the
Internet at: www.2helpU.com.
Batteries
Black & Decker batteries can be recharged many
times. At the end of their useful life, discard batteries
with due care for our environment:
Place the batteries in suitable packaging to ensure that
the terminals cannot be short-circuited.
Take the batteries to a local recycling station.