Home Connect; Setting Up Home Connect - Bosch KAD-Serie Montage- Und Gebrauchsanleitung

en
[filter change]
After 6 months you are prompted via the [filter change]
display message to replace the filter cartridge.
Activating new filter cartridge
When the filter cartridge has been replaced,
the [filter change] function must be re-activated.
1. Change filter cartridge (see chapter "Water filter").
2. Keep pressing the "options" button, until the [filter
change] function is marked with an arrow.
3. Activate by pressing the setting buttons +/-. [filter
change] display goes out.

Home Connect

This appliance is Wi-Fi-capable and can be remotely
controlled using a mobile device.
Note
Wi-Fi is a registered trade mark of the Wi-Fi Alliance.
If the appliance is not connected to the home network,
the appliance functions like a refrigerator without a
network connection, and can still be manually operated
via the controls.
In order to use the Home Connect functions, connect
the appliance to a Home Connect Wi-Fi dongle.
If a Home Connect Wi-Fi dongle is not supplied with
your appliance, you can order this from Customer
Service.
Note
The connection and disconnection of the appliance
plug may be more difficult to perform than expected.
Attach the Wi-Fi dongle at a height of one metre.
Notes
Please observe the safety information in these
■
operating instructions and ensure that this is still
adhered to, even if you operate the appliance via the
Home Connect app and are not at home when doing
so. See the 'Safety and warning information' section.
You must also follow the instructions in the Home
Connect app.
Operation on the appliance always has priority.
■
During this time, it is not possible to operate the
appliance using the Home Connect app.

Setting up Home Connect

Note
To implement settings with Home Connect, you must
have installed the Home Connect app on your mobile
device. Observe the supplied Home Connect
documents with regard to this. Follow the steps
specified by the app to implement the settings.
Note
The Home Connect menu will close automatically when
the appliance is not being operated for a longer period
of time. You can find information on how to open the
Home Connect menu at the start of the appropriate
section.
44
Automatic connection with the home network (WLAN)
If a WLAN router with WPS function is available, the
refrigerator can automatically connect to the home
network.
1. Press the Options button and the Alarm off/lock
button simultaneously.
"Cn" is shown in the freezer compartment display.
Note
Press both buttons simultaneously. The button
operation is locked if only the Alarm off/lock button
is pressed for an excessively long period.
2. Keep pressing the Options button until "AC" is shown
in the freezer compartment display and "OF" is
shown in the refrigerator compartment display.
3. Press the adjustment button +.
The appliance is ready for the automatic connection.
An animation is shown in the refrigerator
compartment display for 2 minutes.
The appliance is ready for the automatic connection
for as long as the animation is displayed.
4. Within those 2 minutes, activate the WPS function on
the home network router (e.g. using the WPS/WLAN
button; observe information on this topic in the router
documentation).
If the connection is successful, "On" flashes in the
refrigerator compartment display.
The refrigerator is ready to connect with the app.
Note
If "OF" is shown in the refrigerator compartment display,
it was not possible to establish a connection.
1. Check whether the refrigerator is located within the
range of the home network (WLAN).
2. Repeat the process or establish the connection
manually.
Manual connection with the home network (WLAN)
If the WLAN router present does not have a WPS
function, or if this is unknown, you can manually
connect the refrigerator with the home network.
1. Press the Options button and the Alarm off/lock
button simultaneously.
"Cn" is shown in the freezer compartment display.
Note
Press both buttons simultaneously. The button
operation is locked if only the Alarm off/lock button
is pressed for an excessively long period.
2. Keep pressing the Options button until "SA" is shown
in the freezer compartment display and "OF" is
shown in the refrigerator compartment display.
3. Press the adjustment button +.
The appliance is ready for the manual connection.
An animation is shown in the refrigerator
compartment display.
The appliance is ready for the manual connection for
as long as the animation is displayed.
4. The refrigerator has now set up its own WLAN
network with the network name "HomeConnect".
You can now access this network with your mobile
device.