Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
1800118683 GV52XX TEFAL:110x154
Use
Steam ironing
• Set the iron temperature adjustment dial and the steam flow adjustment
dial (according to model) to the type of fabric to be ironed (see table below).
• The thermostat light comes on.
• To obtain steam, press on the steam control button on the iron handle
fig.6.
• The steam will stop when you release the button.
T
YPE OF FABRIC
Linen, Cotton
Wool, Silk, Viscose
Synthetic
(Polyester,Acetate,Acrylic, Polyamide)
Mixed fibre fabrics : set the iro-
ning temperature to the setting
for the most delicate fabric.
Woollen garments : press repea-
tedly on the steam control but-
ton - fig.6 to obtain short bursts
of steam, without placing the
iron on the garment itself.
This will avoid making the fabric
shiny.
• Do not press on the steam control button
Vertical steam ironing
• Set the iron temperature dial and the steam flow adjustment
dial (according to model) to the max. position.
• Hang the garment on a coat hanger and hold the fabric
slightly taut with one hand.
• Press repeatedly on the steam control button
iron handle) moving the iron from top to bottom
• VERY IMPORTANT : Before opening your boiler, ensure that there is no more steam left inside by pres-
Never uns-
sing the steam control button
crew the
there is no more steam.
boiler cap
• Stop the generator by pressing the on/off switch and disconnecting the plug.
while it's
• Slowly unscrew the boiler cap.
still stea-
• Using a water jug, fill with maximum 1 litre of water.
ming.
• Fill the boiler fig.4, taking care that the water does not spill over. If this occurs, remove the excess water.
• Replace the boiler cap, screwing on tightly, reconnect your generator to the mains, and switch it on.
• Wait until the boiler heats up. After approximately 8 minutes or when the steam ready indicator light
comes on (according to model), the steam is ready.
22/02/10
•••
S
ETTING THE TEMPERATURE
DIAL
••
•
• Start with the fabrics to be ironed at a low temperature and finish with those
which need higher temperatures (••• or Max).
• To prime the steam circuit, either before using the iron for the first time, or if
you have not used the steam function for a few minutes, press the steam
control button
-
fig.6. several times in a row, holding the iron away from your
clothes.This will enable any cold water to be removed from the steam circuit.
• For delicate fabrics, press the steam control button (on the handle of the
iron) intermittently to avoid possible water droplets appearing with the
steam.
• If you are using starch, it should be sprayed onto the reverse side of the fa-
bric to be ironed.
-
fig.6.
As steam is very hot, never attempt to re-
move creases from a garment while it is
being worn, always hang garment on a coat
hanger. For fabrics other than linen or cotton,
hold the iron a few centimetres from the gar-
-
fig.6.(on the
ment to avoid burning the fabric.
-
fig.7.
- fig.6
located on the handle of the iron and keep it pressed down until
12:15
Page 6
The generator and the iron are
ready to iron when the steam
ready indicator light (according
-
to model) is lit and the iron
thermostat dial light has gone
out.
S
ETTING THE STEAM DIAL
(according to model)
Dry ironing
Filling the boiler during use
GB
D
F
NL
E
P
I
DK
N
S
FIN
TR
GR
PL
CZ
SK
H
SLO
RU
UA
HR
RO
ET
LT
LV
6
Quicklinks ausblenden:
Werbung
Inhaltsverzeichnis
