DeWalt D25602K Bersetzt Von Den Originalanweisungen Seite 23

Setting the Electronic Speed and Impact Control Dial
(Fig. A, C)
D25601, D25602, D25603, D25831
Turn the dial 7 to the desired level. Turn the dial upwards for higher
speed and downwards for lower speed. The required setting is a matter of
experience, e.g.
• when chiselling or drilling in soft, brittle materials or when minimum
break-out is required, set the dial to a low setting;
• when breaking or drilling in harder materials, set the dial to a
high setting.
Setting the Two Stage Mechanical Clutch (Fig. C)
D25602, D25603
NOTICE: Always turn the tool off before changing torque control
settings or damage to the tool may result.
Move the torque control lever 13
for application.
• Clutch Setting 40 Nm 18 is designed for most drilling applications and
is designed to easily clutch out when the drill bit encounters re-bar or
other foreign substances.
• Clutch Setting 80 Nm is designed for higher torque applications
19
such as core-bits and deep hole drilling and is designed to clutch out at
a higher torque threshold.
nOTE: If it is not possible to select position 80 Nm, run the unit under load
and try again.
Each time the tool is plugged in, it will automatically default to clutch
setting 1 into clutch setting 40 Nm
Depth Rod
(Additional Accessory)
1. Push in and hold the depth rod release button on the side handle.
2. Move the depth rod so the distance between the end of the rod and
the end of the bit equals the desired drilling depth.
3. Release the button to lock rod into position. When drilling with the
depth rod, stop when end of rod reaches surface of material.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal injury,
turn tool off and disconnect tool from power source before
making any adjustments or removing/installing attachments
or accessories. Be sure the trigger switch is in the OFF position. An
accidental start-up can cause injury.

WARNING: Tool bits may be hot and gloves should be worn when
changing or removing them to avoid personal injury.

WARNING:
• Be aware of the location of pipework and wiring.
• Apply only a gentle pressure to the tool (approximately 20 kg).
Excessive force does not speed up drilling but decreases tool
performance and may shorten tool life.
• Always hold the tool firmly with both hands and ensure a
secure stance. Always operate the tool with the side handle
properly assembled.
nOTE: Operating temperature is -7˚ to +40˚C (19˚ to 104˚F). Using the tool
outside of this temperature range will decrease the life of the tool.
to setting 40 Nm or 80 Nm as needed
18 , the most sensitive setting.
Proper Hand Position (Fig. F)

WARNING: To reduce the risk of serious personal injury, ALWAYS use
proper hand position as shown.

WARNING: To reduce the risk of serious personal injury, ALWAYS hold
securely in anticipation of a sudden reaction.
Proper hand position requires one hand on the side handle
other hand on the main handle 4 .
Switching On and Off (Fig. A)
D25501, D25601, D25602, D25603
To turn the tool on, depress the trigger switch
To stop the tool, release the trigger switch.
D25601, D25602, D25603
The lock-on slider 2 allows the trigger switch
chiselling mode only. If the lock-on button is activated in drilling mode, as a
feature the tool will switch off automatically.
To turn the tool on, press the trigger switch
To stop the tool, release the switch.
For continuous operation, press and hold down the switch
lock-on button 2 upwards and release the switch.
To stop the tool in continuous operation, press the switch briefly
and release it. Always switch off the tool when work is finished and
before unplugging.
D25820, D25831
To turn the tool on, press the on/off rocker switch
the trigger.
To stop the tool, press the on/off rocker switch at the upper part of
the trigger.
Hammerdrilling
To turn the tool on, press the on/off switch
To stop the tool, release the switch.
Drilling with a Solid Bit (Fig. A)
D25501, D25601, D25602, D25603
1. Insert the appropriate drill bit.
2. Set the mode selector switch 6
3. D25601, D25602, D25603 only: Set the electronic speed and impact
control dial 7 .
4. Fit and adjust the side handle
3
5. Mark the spot where the hole is to be drilled.
6. Place the drill bit on the spot and switch on the tool.
7. Always switch off the tool when work is finished and
before unplugging.
Drilling with a Core Bit (Fig. A)
1. Insert the appropriate core bit.
2. Assemble the centerdrill into the core bit.
3. Set the mode selector switch 6
4. D25601, D25602, D25603 only: Turn the electronic speed and impact
control dial to a medium or high speed setting.
7
5. Fit and adjust the side handle 3
6. Place the centerdrill on the spot and switch on the tool. Drill until the
core penetrates into the concrete approximately 1 cm.
7. Stop the tool and remove the centerdrill. Place the core bit back into the
hole and continue drilling.
8. When drilling through a structure thicker than the depth of the core
bit, break away the round cylinder of concrete or core inside the bit at
regular intervals.
To avoid unwanted breaking away of concrete around the hole, first drill
EngLIsH
, with the
3
1 .
1 to be locked on in
1 .
, slide the
1
1 at the lower part of
1 .
to the hammerdrilling position.
.
to the hammerdrilling position.
.
21