Noise/Vibration Information; Charging The Battery - Bosch GWS Professional 18 V-LI Originalbetriebsanleitung

(15) Carbide grinding head A)
(16) Protective guard for cutting
(17) Cutting disc A)
(18) Hand guard A)
(19) Rubber sanding pad A)
(20) Abrasive disc A)
(21) Round nut A)
(22) Cup brush A)
(23) Handle (insulated gripping surface)
(24) Extraction guard for cutting with a guide block
(25) Diamond cutting disc
A)
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Angle grinder
Max. grinding disc diameter
Grinding spindle thread
Max. thread length of grinding spindle
Weight according to EPTA-Procedure 01:2014
Recommended ambient temperature during charging
Permitted ambient temperature during operation
during storage
Recommended batteries
Recommended chargers
A) Depends on battery in use
B) Limited performance at temperatures <0 °C

Noise/Vibration Information

Noise emission values determined according to
EN 60745-2-3.
Typically, the A-weighted noise level of the power
tool is: Sound pressure level 82 dB(A); sound power
level 93 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and
h
uncertainty K determined according to EN 60745-2-3:
Surface grinding (roughing): a
h
Disc sanding:
a = 2.5 m/s 2 , K = 1.5 m/s 2 .
h
The vibration level given in these instructions has been
measured in accordance with a standardised measuring
procedure and may be used to compare power tools. It
can also be used for a preliminary estimation of
exposure to vibration.
Bosch Power Tools
English | 27
A)
A)
Fitting
A)
and
B)

Charging the battery

= 6.0 m/s , K = 1.5 m/s ,
2 2
The stated vibration level applies to the main
applications of the power tool. However, if the power
tool is used for different applications, with different
application tools or poorly maintained, the vibration
level may differ. This can significantly increase the
exposure to vibration over the total working period.
To estimate the exposure to vibration accurately, the
times when the tool is switched off or when it is running
but not actually being used should also be taken into
account. This can significantly reduce the exposure to
vibration over the total working period.
Implement additional safety measures to protect the
operator from the effects of vibration, such as servicing
the power tool and application tools, keeping the hands
warm, and organising workflows correctly.
GWS 18 V-LI
mm 115
M 14
mm
kg 2.0–3.0
°C 0 to +35
°C –20 to +50
GBA 18V...
ProCORE18V...
GAL 18...
GAX 18...
GAL 36...
 Use only the chargers listed in the technical data.
Only these chargers are matched to the lithium-ion
battery of your power tool.
Note: The battery is supplied partially charged. To
ensure full battery capacity, fully charge the battery in
the charger before using your power tool for the first
time.
The lithium-ion battery can be charged at any time
without reducing its service life. Interrupting the
charging process does not damage the battery.
The lithium-ion battery is protected against deep
discharge by the "Electronic Cell Protection (ECP)".
When the battery is discharged, the power tool is
switched off by means of a protective circuit: The
application tool no longer rotates.
 Do not continue to press the On/Off switch after the
power tool has automatically switched off. The
battery can be damaged.
Follow the instructions on correct disposal.
GWS 18V-125 V-LI
125
M 14
22 22
2.0–3.0
0 to +35
–20 to +50
GBA 18V...
ProCORE18V...
GAL 18...
GAX 18...
GAL 36...
1 609 92A 5C4 | (04.03.2020)