Noise/Vibration Information - Bosch GWS 9-125 S Professional Originalbetriebsanleitung

OBJ_BUCH-3021-001.book Page 19 Friday, August 18, 2017 12:40 PM
Angle Grinder
Speed preselection
Restarting Protection
Weight according to EPTA-Procedure
01:2014
– with vibration-damping auxiliary handle
– with standard-auxiliary handle
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.

Noise/Vibration Information

Sound emission values determined according to
EN 60745-2-3.
Typically the A-weighted noise levels of the product are:
Sound pressure level 93 dB(A); Sound power level
104 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-3:
2
Surface grinding: a =7.5 m/s , K=1.5 m/s
h
2
Disk sanding: a =7.5 m/s , K=1.5 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Assembly
Mounting the Protective Devices
 Before any work on the machine itself, pull the mains
plug.
Note: After breakage of the grinding disc during operation or
damage to the holding fixtures on the protection guard/power
tool, the machine must promptly be sent to an after-sales ser-
vice agent for maintenance. For addresses, see section "Af-
ter-sales Service and Application Service".
Bosch Power Tools
GWS...
kg
kg
Protection Guard for Grinding
2
,
2
.
tion guard 8 to the requirements of the work process. For this,
press the release lever 7 upward and turn the protection
guard 8 to the required position.
 Always adjust the protection guard 8 in such a manner
that all 3 red cams of release lever 7 engage into the
corresponding notches of the protection guard 8.
 Adjust the protection guard 8 in such a manner that
sparking is prevented in the direction of the operator.
 The protection guard 8 may be turned only upon actua-
tion of the release lever 7! Otherwise the power tool
may not continue to be used under any circumstances
and must be taken to an after-sales service agent.
Note: The encoding keys on the protection guard 8 ensure
that only a protection guard that fits the machine type can be
mounted.
Protection Guard for Cutting
 For cutting with bonded abrasives, always use the pro-
tection guard for cutting 14.
 Provide for sufficient dust extraction when cutting
stone.
The protection guard for cutting 14 is mounted in the same
manner as the protection guard for grinding 8.
Auxiliary Handle
 Operate your machine only with the auxiliary handle 4.
Screw the auxiliary handle 4 on the right or left of the machine
head depending on the working method.
English | 19
9-115 S 9-125 S


2.0 2.0
1.9 1.9
/II /II
Place the protection guard 8 on
the power tool's holding fixture
until the protection guard's cod-
ing lugs line up with the holding
fixture. When doing so, press and
hold the unlocking lever 7.
Press the protection guard 8 onto
the spindle collar until the shoul-
der of the protection guard is
seated against the flange of the
machine, and turn the protection
guard until it can clearly be heard
to engage.
Adjust the position of the protec-
1 609 92A 3FS | (18.8.17)

