Recommended Separation Distances - Masimo Radius T Handbuch

ENVIRONMENTAL
Storage/Transport Temperature
Operating Temperature
Storage/Transport Humidity
Operating Humidity
Atmospheric Pressure
WIRELESS TECHNOLOGY INFORMATION
Type
Data Transmission Rate
Max. Output Power
Modulation Type
Frequency Range
Antenna Peak Gain
FCC ID are as follows: FCC ID: VKF-RADIUST, IC ID: 7362A- RADIUS T
CAUTION: In order to maintain Bluetooth connectivity with the host device ensure that Radius T° is within specified distance
and line of sight of the host device.
RF Radiation Exposure Statement: This equipment has been exempted from FCC RF radiation exposure testing and IC RSS 102
RF radiation exposure limits set forth for an uncontrolled environment.
Note: This device complies with part 15 of FCC Rules and Industry Canada's license-exempt RSSs. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accor-
dance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the inter-
ference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Note: When using Radius T° consideration should be taken to local government frequency allocations and technical parame-
ters to minimize the possibility of interference to/from other wireless devices.

RECOMMENDED SEPARATION DISTANCES

The ME Equipment is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the ME Equipment
can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the ME
Equipment as recommended below, according to the maximum output power of the communication equipment.
RATED MAXIMUM OUTPUT POWER OF TRANSMITTER (W)
0.01
0.1
1
10
100
For transmitters rated at a maximum output power not listed above, the recommended separation distance (d) in meters (m) can be estimated using the equation applicable
to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer.
Note 1: At 80 MHz and 800 MHz, the higher frequency range applies.
Note 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people.
The ME Equipment is intended for use in the electromagnetic environment specified below. The customer or the user of the ME Equipment should assure that it is used in
such an environment.
EMISSION TEST
RF Emissions
CISPR 11
RF Emissions
CISPR 11
-20°C to 50°C @ ambient humidity
10°C to 40°C @ ambient humidity
10% RH to 95% RH (non-condensing) @ ambient temperature
10% RH to 95% RH (non-condensing) @ ambient temperature
700 to 1060 hPa @ ambient temperature and humidity
Bluetooth Low Energy
Minimum packet rate of 0.0167 Hz (1/60 Hz)
(EIRP): 9.9 dBm
GFSK
2402–2480 MHz
+5.67dBi
RECOMMENDED SEPARATION DISTANCE BETWEEN PORTABLE AND
MOBILE RF COMMUNICATION EQUIPMENT AND THE ME EQUIPMENT
80 MHz to 800 MHz
d = 1.17*√P
0.12
0.37
1.17
3.7
11.7
GUIDANCE AND MANUFAC TURER'S DECLARATION- ELEC TROMAGNETIC EMISSIONS
COMPLIANCE
The ME Equipment must emit electromagnetic energy in order to perform its intended function. Nearby
Group 1
electronic equipment may be affected.
Class B Suitable for use in all establishments, including domestic environments.
SEPARATION DISTANCE ACCORDING TO FREQUENC Y OF TRANSMITTER (M)
ELEC TROMAGNETIC ENVIRONMENT - GUIDANCE
5
800 MHz a 2.5 GHz
d = 2.33*√P
0.23
0.74
2.33
7.37
23.3
10714C-eIFU-0920